文件名称:
Motorola GM300无线电台 8 信道改16信道软件及说明（说明为英文版）
开发工具:
文件大小: 452kb
下载次数: 0
上传时间: 2019-04-12
详细说明： Motorola GM300无线电台 8 信道改16信道改造方法 Radio Programming, 8 to 16 channel expansion Introduction. The Motorola GM300 can be re-programmed quite easily to allow use on our Amateur Radio bands. The radio is made in both a VHF and UHF versions, and makes an excellent 2mtr or 70cms mobile/base station radio. Most of the radios I have worked on have originally been 8 channel units. These can be modified to operate on 16 channels quite easily. The programming interface can be made for a low cost. All it consists of is a RS232 to TTL level converter, that connects between the serial port of your PC and the radios microphone socket. Amateur Radio Conversion. The radio requires the Motorola Software which can be found if you ask around or search for it on the FTP sites on the Internet. If you cant find it then try your local Motorola dealer who should be able to help at a small cost. You also have to make an interface, or purchase one. To program the radio onto the Amateur band, you can find some versions of software that have been hacked into allowing frequencies to be entered to bring the radio into the amateur bands which normally are just bellow the original working frequency. However this depends on your version of software, if its a un-hacked version then you have to press the key down when entering the frequency. You must release the key when entering the decimal point. For example to program 433.500MHz you will enter the following: $££.%)) on a English layout keyboard. (This is 433.500 with the held down. Fill all of the 0s in the frequency field. This example is the same for both the VHF and UHF GM300s. 16 Channel conversion. (for 8 channel radios only) To program the radio for 16 channels all you need to do is edit a file called GM300.MDF. You do this with the help of a Hex editor such as Hex Workshop (see my PC links page to go to the home of Hex Workshop, an evaluation version is available to download for free) . The file you need to modify is called GM300.MDF and can be found in the main directory of the Motorola software. Keep a backup of your original GM300.MDF file, just in case you make a mistake. I have made a small video that shows the Hex Workshop screen during the modification. This should help you understand the procedure of editing the file which when complete will give you 16 channels. Click below to download. gm300mdf.zip (236Kb) Procedure 1. Get a copy of Hex Workshop 2. Start the Hex Workshop program and open the file GP300.MDF to begin editing. 3. Go to "Tools", and the "Generate Checksum". 4. Make sure "Entire Document" and also "Decimal" are ticked. Then press "Generate". 5. Look in the "Checksum-16" box, in my version of software for example this results in a checksum of 5514. (yours may be a different number depending on the version of Motorola software) 6. Write this number down, as you need it later. 7. Press "Cancel" to return to the main window and your next step. 8. Go to "Edit" and then "Find". A pop-up window appears. 9. You need to enter the model number of your radio. For e.g. M34GMC00D3AA. 10. When you enter the model number leave off the last two letters(AB on my radio).Make sure "ASCII" is ticked. 11. When you press "Find Next", you will see your model number highlighted. 12. If you count 8 numbers after the highlighted section, you should see the number "08" as long your radio is originally a 8 channel set. 13. . 14. You now need to edit the start of the program, to allow the software to run. 15. In the first few lines look for a Hex number that you can easily take away 8 from. 16. In my software at address 00000040 you will see the number "78" on the right. 17. Edit this to be "70". 18. Now you must do a final checksum and make sure it equals the original value. 19. If this is the same, then replace you original file with the modified file. 20. Try to reprogram your radio with the extra 8 channels to give you 16 channels. The hex workshop 8 to 16 channel upgrade only works with models that have a 3aa at the end of there model mumbers. ALso if someone knows how to increase the memory in the gm300 it possible to increase to 32 channels or more. The software doesnt care its restricted by the memory in the radio itself. Edit the "08" to "10" (note 10 in Hex is equal to 16 in decimal)
(系统自动生成,下载前可以参看下载内容)
下载文件列表
相关说明
- 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
- 本站是交换下载平台，提供交流渠道，下载内容来自于网络，除下载问题外，其它问题请自行百度。
- 本站已设置防盗链，请勿用迅雷、QQ旋风等多线程下载软件下载资源，下载后用WinRAR最新版进行解压.
- 如果您发现内容无法下载，请稍后再次尝试；或者到消费记录里找到下载记录反馈给我们.
- 下载后发现下载的内容跟说明不相乎，请到消费记录里找到下载记录反馈给我们，经确认后退回积分.
- 如下载前有疑问，可以通过点击"提供者"的名字，查看对方的联系方式，联系对方咨询.
相关搜索:
