COPAL CS-32 转动选择开关（Selector Switches）.pdfCOPAL CS-

文件名称: COPAL CS-32 转动选择开关（Selector Switches）.pdf

所属分类: 其它

开发工具:

文件大小: 119kb

下载次数: 0

上传时间: 2019-10-15

提供者: weixin_********

下载 (119kb)

不能下载？报告错误

详细说明：COPAL CS-32 转动选择开关（Selector Switches）pdf,COPAL CS-32 转动选择开关（Selector Switches）COPAL ELECTRONICS CS-32 ROTARY SELECTOR SWITCHES ( SMD STANDARD SPECIFICATIONS ELECTRICAL CHARACTERISTICS Circuit type 1 pole 2 contacts Contact rating 0.5VA Operating temperature range Maximum current 100mA 40~85°0 Maximum voltage 16V Storage temperature range Sealing Washable by"“ 0"ring Contact timing Non-shorting Approx 0.05g(A, B) Contact resistance 2 maximum Net w/eight Approx 0.06g(C) Appro×.0.11g(G,H) Insulation resistance 100 MQ(DC500V)minimum Dielectric strength AC250V,60s MECHANICAL CHARACTERISTICS No. of positions ENVIRONMENTAL CHARACTERISTICS Adjustment torque 5 mN.m 151 gf-cm) maximum Amplitude 1.5 mm or Stopper strength Acceleration 98 m/s2 20 mN m (204 gfcm) minimum Vibration 10-500-10Hz, 3 directions for 10 cycles each Stepping angle 250°±15° Shock 490m/s2,11 e directions for 3 times each Solderability snCu(ead-re):245±3°c.2~3s Load life 50 cycles minimum DC16V30 mA Humidity(Steady state) 40C, Relative humidity 90-95/, 240 h Sn-Cu(Lead-tree High temperature exposure 85°C.96h Fow:260±3° as the temperature in a pot of molten solder emersion from head of ter- LoW temperature exposure 40°C.96h Soldering heat minal to backside of board 5-6s two times maximum Thermal shock -40(0.5h)~85°C(0.5h).5 cycles Reflow: Peak temperature 255C ( Please refer to the profile below. Manual soldering:350±10°C,3~4s Shear(Adhesion) 5N0.51kgf,10s (°C) 250 Peak:2500°C Substrate bending Width 90 mm bend 3 mm. 5s. 1 time over230°0 Pull-off strength 5N10.51kgf,10s g200 Pre Heating Zone 名 180°0 I 1: Reference only 2 150- 150 C 90±30s 100 30±10s 50 Heating time Soldering Zone Reflow: two times maximum Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan, 2007 COPAL ELECTRONICS C5-37 ROTARY SELECTOR SWITCHES ( SMD ■ OUTLINE DIMENSIONS Unless otherwise specified, tolerance: +0.3(Unit: mm) ●cs-32-12zEA Production date code Lead- free ldentification mark 1 dig t (Location reversed every 2 years) cW345Wx19-×0.45D 0.05 ●cs-32-122EB Production date code Lead- free Identificaticn mark 1 digit (Location reversed every 2 years) cW340005M×19L×045D 0.05 ●cs-32-12zEc Production date code 05W×1.9L×045D Lead-free ldentification mark 1 digit Location reversed every 2 years) t=0.12 ⊥2-0.7 3.4 4±1 →TCM No plating on the cut surface ●cs-32-12zEG Prcduction date code 02 Operating face 2-0.6 Lead-free Identification mark 1 digit(Location reversed every 2 years) CW, (C) CCW 3.6 t=0.12 a Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan. 2007 COPAL ELECTRONICS CS-32 ROTARY SELECTOR SWITCHES ( SMD ■ OUTLINE DIMENSIONS Unless otherwise specified, tolerance: +0. 3(Unit mm) ●Cs32-12ZEH 3.5 Prod」 ction dare code& 0.5Wx1.9L×0.45D Operating face Lead-free ldentification mark 1 digit i Location reversed every 2 years, c ccw t=0.12 3.6 RECOMMENDED P.C.B. PAD OUTLINE DIMENSIONS ●cs-32-12zEA,12ZEG ●cs-32-12zEB.12ZEH (Unit: mm) 40 120812 20812 Note 1)The zero point is the center of mounting Note 2)The land patterns conform to EIAJ RC2161 Note 3) The land patterns are for reflow soldering Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan, 2007 COPAL ELECTRONICS C5-37 ROTARY SELECTOR SWITCHES ( SMD PACKAGING SPECIFICATIONS O Taping version is packaged in 500 pcs per reel Orders will be accepted for units of 500 pcs, i. e, 500, 1000, 1500 pCS,, etc O CS-32ZETA and ZETB versions are boxed with 4 reels(2000 pcs. CS-32ZETG and ZETH versions are boxed with one reel (500 pcs. Maximum number of consecutive missing pieces =2 Leader length and reel dimension are shown in the dia-grams below O Embossed tape dimensions ● Reel dimensions Unit: mm) (Conforms to JIS C 0806-3) (In accordance with ElAJ ET-7200A) 130(ETA/ETB) 134∈ ETG/ETH) Fill End 囗…口囗图…-图团 20 pitches min Direction of feed Leader /13+02 400 mm min 15.4+1 (ETAETB o 180-i5(Top setting type) 17.4±1(ETG/ETH) 254±2( de setting type OCS-32-12ZETA/CS-32-12ZETB CS-32-12ZETG/CS-32-12ZETH nit: mm (Conforms to JIS C 0806 2+005 0.4±0.1 ation example Installation example (CS-32EA) 6+2 Direr"ion of feed O The smallest unit of bulk pack in a plastic bag is 10 pcs per pack. Orders will be accepted for unit of minimum 10 pcs:1.e 10,20,30pcs.,etc O Boxing of bulk in a plastic bag is performed with 100 pcs (standard 500 pcs. per box a Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan. 2007

(系统自动生成,下载前可以参看下载内容)