文件名称:
科瑞利华Rechner磁性开关说明书.pdf
开发工具:
文件大小: 542kb
下载次数: 0
上传时间: 2019-10-15
详细说明:科瑞利华Rechner磁性开关说明书pdf,科瑞利华Rechner磁性开关说明书SENSORS
TABLE OF CONTENTS
CATALOGUE MAGNETO-RESISTNE SENSORS
MRS
PAGES
TECHNOLOGY· MOUNTING· APPLICATION∴.4-6
ADJUSTMENT
TECHNICAL TERMS
日面
APPLICATION EXAMPLES
8
TYPE CODE.…
CYLINDRICAL HOUSINGS
…11-19
NORMS
20-21
TYPE SELECTION IN ARTICLE NUMBER ORDER
22
TYPE SELECTION IN TYPE DESCRIPTION ORDER
22
o030c059
品≌O
RECHNER Industris-Elekironk GmbH. Gaullstralle 8-10 D-68623 Lamperheim Tel +49(0)62 05 50 (7-0. Fax +49(0)562 06 50 07-20email in o(rechner-sensors ce. ww.rechner-sensors de 3
SENSORS
TECHNOLOGY· MOUNTING· APPLICATION
The magnetoresistive sensors(MRS )detect the movement of ferromagnetic materials, by means of the
change of the magnetic flow. They are suitable for rotary speed sensing, for detection of gearwheels and
for standstill control. Areas of use can be heavy construction engines, rail vehicles, large diesel engines
and turbines
The magnetoresistive sensors(MRS)work like a magnetic Wheatstone bridge. They react to all
ferromagnetic materials. The tooth or gap of a gearwheel, which passed the active area of the sensor,
have a different influence on the magnetic field. This results in a change of the magnet-field dependent
resistor. This change of the magnetic field is transformed to an electrical voltage-bridge, which then is
filtered and prepared. The output signal is a voltage, which corresponds to the magnetfield change
We have two different series
→ Series300
-s
3-wire pnp or nen
2-wire
→ Series350
4-wire pne or nen
4-wire PNP with dephased output signal
with detection of direction of rotation
The components of the MrS are mounted in plastic or metal casings and encapsulated with epoxy casting
resin
The plastics used for the housings are
E PA(polyamide)6.6 glass-fibre reinforced
E PEEK (polyetheretherketone)
And the metal housings are
A VA stainless-steel, material No. 1. 4404 or No. 1.4305
E MS brass/chrome or nickel-plated
Since the active area is made from a block material the degree of protection IP 68 is achieved on the front e
end
Only pre-tested electronic components, proven integrated circuits and hybrid circuits are used and pro -5
duced with SMT. The standard constant ambient temperature permitted is dependent on the model
from -40 up to+125 C(see data sheet)
With contactless detection no physical actuating force is required for operation. There is no contact bounce, t
no sensor wear, no maintenance and the service lite is independent of the switching frequency
MRS can be used in machines, systems and vehicles for contactless detection, for monitoring and
positioning, as a pulse generator for counting tasks and speed measurements, and for many other
applications (for application examples see page 8)
RechNerIndustrie-elektronikGmbh.Gaulsstralse8-10.d-68623LampertheimTel.+49(0)62065007-0.fax+9(0)62065007-20.emailinto(arechner-sensors.de.www.recmer-sansors.de
SENSORS
Wiring of the MRs should be routed separately or screened from heavy conductor lines, as in extreme
cases inductive peak voltages can destroy the sensors despite the integrated protective circuit. Screened
cable or twisted lines are recommended, especially for longer cable runs> 5 m Direct control of electric
light bulbs is to be avoided, because during the switch-on moment cold current is many times the rated
current and can destroy the output stage of the sensor
Units with strong local field power, e. g. high power walkie-talkies, or noise sources in the lower fre
quency range, e.g. long, middle or short wave transmitters should not be operated close to the sensors or
additional measures have to be taken in order to eliminate the maloperation
2-and 3-wire sensors with binary output can be used in series or parallel connection, similar to mechanical
contacts. It is important to note the type-typical voltage drop and the residual voltage Ua, that must be
multiplied, for series connection, in accordance with the number of sensors
Series connection
Parallel connection
2 wire DC
四刚
3 wire DC NPN
3 wire DC PnP
o030c059
人z
RecHnErIndustrie-elekIronkGmbh.gaUllstrAlse8-10.D-68623lAmperheim.Tel.+-19(0)62055007-0.Fax-49(062065007-20.emailino(rechner-sensors.ce.www.rechner-sensors.de5
SENSORS
The material and version-dependent maximum torque should be taken into consideration when mounting
in order to prevent damage to the threaded sleeves. The values listed in the table are based on the use of
the nuts supplied with the sensors
Housing Materia
Thread
PVC
PA6.6
PTFE
Brass
Stainless steel
M5x0.5
1.5 Nm
M 8x1
4.5Nm
M12X1
1.5Nm
1 Nm
0.2Nm
16 Nm
25 Nm
M18x1
1.7Nm
0.5Nm
28 Nm
60 Nm
M22X1.5
12 Nm
6 Nm
1.4Nm
32 Nm
84 Nm
M30x1.5
8 Nm
2.5Nm
82 Nm
200Nm
M32X1.5
13 Nm
3 Nm
150Nm
230N
Due to the permitted thread tolerances specified in German standard DIN 13, the maximum screw-in
length for threaded sensors should be taken into consideration. Depending on that the length of the
threaded block for screwing in proximity sensors should not exceed the following dimensions. In the case
of larger threaded blocks we recommend drilling a blind hole in order to adhere to the maximum screw-in
length
Thread
M5×05
Max 1
M12x1
M18×1M22×15M30×15M32x15
Screw-in length
3 mm
6
mm
8
12 mm
12 mm
12 mm
12 mm
m
ax
ADJUSTMENT
Speed sensing is possible with gearwheels down to module 1 at a maximum switching frequency of 15
KHZ For detecting rotary speed/direction of rotation magnetoresistive sensors(MRS)must be mounted
radially with respect to the direction of motion and with their marking set vertically to it
The dependence of the modul of the detected gearwheel on the mounting distance and the maximum
detecting frequency is as follows:
Distance [mm]
Module 4
Module 2
2.5
2
Module 1
0,5
Example: MRS-300-M18.0
100
10000
Frequence [Hz]
6 RECHNER Industis-Elekaronk GmbH, Gaulstalke 8-10 D 68623 Lampertheim Tel, +19(0)62 06 50 07-D Fax +19(0)62 06 50 07-20 email intorechner sensors de wmrecnsr-segnsorsde
SENSORS
TECHNICAL TERMS
Unless otherwise specified technical data is as follows: +24C, U.= 24 V dC
Operating sensing distance /S
Within the operating sensing distance the sensor operates reliably taking in to account all the possible
tolerances, t lies between 0 and 0.81x S
Power up time delay
The time the sensor needs to be ready for operation after connecting the operating voltage. It is in the
milliseconds range
lousing materials
The application of the housing materials used is based on the technical specifications of the material and
of the manufacturer. The customer is responsible for checking in each case that the housing material is
suitable for the application, even though RECHNER Sensors have far-reaching application experience
concerning the use of different housing materials
Cable
For the standard models pvc- or Pur-cable are used. one has to take into consideration that the cable
should not be moved with ambient temperatures below -5C. Pvc is not suitable for use in applications
with oil-based liquids or with UV-radiation. PUR is not suitable for continuous contact with water. For
special application areas silicone or PTFE cables are available
Nominal sensing distance /s
The characteristic value of a sensor, without consideration of production tolerances and variations due to
temperature and voltages. Reference gearwheel module 4, 1000 Hz
Real sensing distance /S
The sensing distance determined at +20C and rated voltage. Here the series variance is taken into
consideration. Variation max. 10 %o
Series-and paralle/ connection
It is possible to connect the sensors in series or parallel. When considering this it must be taken into
account that the voltage drops are added for series connection and the residual voltages for parallel
connection. Under these circumstances it is advisable to operate a maximum of three sensors in a
corresponding circuit
Frequency of operating cycles
The maximum damping and un-damping cycles of the proximity sensor within one second. To ascertain
g the frequency of operating cycles a pulse /break ratio of 1: 2 is used as a basis
e Enclosure rating
8 IP 65: Protection against contact with voltage-carrying parts, protection against ingress of dust and water jet
s IP 67: Protection against contact with voltage-carrying parts, protection against ingress of durst and
protection against ingress of water when the equipment is immersed in water, up to 1 m depths and for a
a period of 30 minutes
Temperature variation
o The displacement of the switching point if the ambient temperature changes. This is with MRS less then
+10%
2 Modul
g Diameter of a gearwheel in relation to the number of teeth M=D: T
RecHnErIndustris-elekTronkGmbh.Gaullstralle8-10.D-68623Lamperheim.tEl.+49(0)62055007-0.Fax-49(0)52065007-20.emailino(rechner-sensorsce.www.rechner-sensors.de7
SENSORS
APPLICATION EXAMPLES
Detection of a gear wheel or cam whee
Detection of the motion of a bolt during
the cement production
Detection of the rotation of an electric 2
driving machine
SENSORS
TYPE CODE
MRS
existing
with flange connector
if exist
Oc= open collector
existing
K.= special housing material
with 3 or 4-wire
0= NC
s
dephased output signal
N
2-wire DC
10=3or4
DC PNP
20 =3 or 4-wire DC NPN
10.16. M..= Version /thread size
300= Speed control
350= Speed control / with detection of direction of rotation
Magneto-resistive sensor
g
RECHNER Industris-Elekironk GmbH. Gaullstralle 8-10 D-68623 Lamperheim Tel +49(0)62 05 50 (7-0. Fax +49(0)562 06 50 07-20email in o(rechner-sensors ce. ww.rechner-sensors de 9
SENSORS
c=0305590g2
10 ECHNER Industrie-Ek800+502:m99
(系统自动生成,下载前可以参看下载内容)
下载文件列表
相关说明
- 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
- 本站是交换下载平台,提供交流渠道,下载内容来自于网络,除下载问题外,其它问题请自行百度。
- 本站已设置防盗链,请勿用迅雷、QQ旋风等多线程下载软件下载资源,下载后用WinRAR最新版进行解压.
- 如果您发现内容无法下载,请稍后再次尝试;或者到消费记录里找到下载记录反馈给我们.
- 下载后发现下载的内容跟说明不相乎,请到消费记录里找到下载记录反馈给我们,经确认后退回积分.
- 如下载前有疑问,可以通过点击"提供者"的名字,查看对方的联系方式,联系对方咨询.