AB直流调速器1397用户手册.pdfAB直流调速器1397用户手册pdf,AB直流调速器1397用

文件名称: AB直流调速器1397用户手册.pdf

所属分类: 其它

开发工具:

文件大小: 3mb

下载次数: 0

上传时间: 2019-10-12

提供者: weixin_********

下载 (3mb)

不能下载？报告错误

详细说明：AB直流调速器1397用户手册pdf,AB直流调速器1397用户手册Summary of Changes Summary of changes Description of New or Updated Information Page Type FS2/FS3 Control Options 1-4 Updated 200%o Overload Capacity l-4 Updated Publication 1397-5.0-June 2001 Table of contents Introduction Chapter 1 Manual Objectives Chapter Objective 1-2 Storage Conditions 1-2 Drive Identification Nameplate 2 Firmware Version 1-2 Catalog Numbering Convention 1-3 Specifications Power Ratings and Supply Capacity(230/460VAC) 1-6 Power Ratings and Supply Capacity(380/415VAC) 1-6 Drive 1/0 Specifications Logic Inputs 1-7 Logic output 1-7 Analog Inputs 18 Analog outputs 1-8 Drive Description Options 1-10 Installation Chapter 2 Chapter objectives 2-1 Environment 2-1 2-1 Cooling airflow 2-2 Line Filters (CE Only) 翻意1 II8 D 2-2 AC Line Inductors(CE Only) 2-2 Enclosure Mounting Minimum Clearances 23 Enclosure Mounting Dimensions 24 Grounding procedures 2-8 Wiring clearance 2-14 Disconnect 2-14 24V Power Supply 2-14 Wire Size, Type Class 2-15 Motor installation 2-17 Power Wiring procedure 2-17 AC Line Torque Recommendations 2-24 Recommended ac Line and DC armature Fuses 2-25 Control connections 230 Control Wiring Procedure 2-3 Publication 1397-5.0 -June 2001 Table of contents Programming Terminal Chapter 3 General HIM Description HIM Operation 3-5 HIM Programming St 3-6 HIM Programming Modes 3-7 Program and Display Modes 3-7 Bit enums Process Mode 3-8 EEprom Mode 3-9 Search Mode 3-12 Control status Mode 3-12 Start-Up and Adjustment Chapter 4 Introduction......,.. 4- Required Tools and Equipment 4-2 Recommended Tools and Equipmen 4-2 G eneral 4-2 Drive Hardware Adjustments 4-3 Motor ground check 4-6 Pre-Power Checks 4-6 Pre-Power Checklist 4-7 Field Supply Configuration 4-8 Power-On Check 4-14 Parameter Set-Up 4-15 Parameter Madification Sequence ........4-17 Jumper Settings 4-20 ify the Correct Operation of 24V v/O Inputs 4-26 Motor and Feedback Polarity Checks 4-29 autotuning 4-35 Auto-Tune Set-Up 着11 4-36 Auto-Tune Execution 4-37 Application Set 4-38 Programming Parameters Chapter 5 Introduction Record Keepin 5-1 Safety Precautions 5-2 Parameter Groups 5-2 Numeric Parameter Table 5-6 Parameter Descriptions(By Group 5-14 Parameters(Alphabetical) 5-97 Hidden parameters Publi 97-5.0-June,2001 Table of contents Ⅲ Troubleshooting Chapter 6 Introduction 6-1 Required Equipment 6 HIM Fault Display 6-2 Clearing a fault 6-2 Clearing an Alarm 6-2 Fault Description Table 6-3 Alarm Description Table 6-7 irmware Block Diagram Appendix A Standard Inputs A-1 10 Expansion Inputs A-2 Speed/Trim Reference Select A-3 Speed Reference Ramp A-4 Outer Control Loop A-5 Speed Reference Mode select A-6 Speed Lool A-7 Current Minor Loop reference A-8 Current Minor Loop A-9 Field Control lo A-10 Standard Outputs A-11 Level detectors 11非 A-12 10 Expansion Outputs -13 CE Conformity ppendix B A EMC Compliance B-1 EMC Requirements B-1 Equipment requirements B-1 Mounting the Equipment B-4 Grounding Requirements B-8 g the Equipment B-10 erating Appendix C High ambient Temperature Conditions 1,1 C-1 Derating for High Altitude C-2 Air Conditioning C-2 Space Heaters C-2 Publication 1397-5.0 -June 2001 Table of contents Using SCANport Appendix D Capabilities Chapter objectives D-1 Logic status Parameter D-1 Configuring the scanport controls D-3 Setting the Loss of Communications Fault D-5 Using the SCANport I/O Image D-5 Supported SCANport Messages D-11 Logic Status Format D-12 Logic command Format D-12 User Parameter value table D-13 Lifting Instructions AppendIx E Introduction Lifting Component Ratings E-1 Drive Mounting E-1 Publi 97-5.0-June,2001 Chapter Introduction Manual objectives The purpose of this manual is to provide you with the necessary information to install, program, start up and maintain the 1397 DC Drive. This manual should be read in its entirety before operating servicing or initializing the 1397 Drive. This manual must be consulted first, as it will reference other 1397 manuals for option initialization This manual is intended for qualified service personnel responsible or setting up and servicing the 1397 DC Drive. You must have previous experience with and a basic understanding of electrical terminology, programming procedures, required equipment and safety precautions, as typical applications will consist of a properly rated DC motor, with or without feedback based on performance requirements, and the 1397 △ ATTENTION: Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved should install adjust, operate and/or service this equipment. Read and understand this section in its entirety before proceeding. Failure to observe this precaution could result in bodily injury or loss of life ATTENTION: An incorrectly installed or applied drive can result in component damage or a reduction in product life. Wiring or application errors such as undersizing the motor, incorrect or inadequate AC supply or excessive ambient temperatures may result in damage to the drive or motor ATTENTION: This drive contains ESD(Electrostatic Discharge) sensitive parts and assemblies Static control precautions are required when installin testing, servicing or repairing this assembly Component damage may result if esd control procedures are not followed. If you are not familiar with static control procedures, reference Allen-Bradley Publication 8000-4.5.2, Guarding against Electrostatic Damage or any other applicable esd protection handbook. Publication 1397-5.0- June 2001 Introduction Chapter Objective Chapter 1 in addition to detailing drive features and specifications also supplies the information needed to unpack, properly inspect and if necessary, store the 1397 Drive. A complete explanation of the catalog numbering system is also included in this chapter Storage Conditions After receipt inspection, repack the Drive in its original shipping container until ready for installation. To ensure satisfactory operation at startup and to maintain warranty coverage, store the Drive as follows In its original shipping container in a clean, dry, safe place In an ambient temperature that does not exceed 65C(149 F)or go below-30C(-22°F) Within a relative humidity range of 5 to 95%0 without condensation e At an altitude of less than 3,000 meters(10,000 ft )above sea Drive ldentification The 1397 DC Drive has a nameplate on the side of the chassis Nameplate (Fig. II) that identifies the specific model number design, applicable AC input power and dC output power data. All communication concerning this product should refer to the appropriate model number information Fiqure 1 Bulletin 1397 Nameplate AB ALLEN-BRADLEY A ROCKWELL INTERNATIONAL COMPANY BULLETIN 1397 MN1397-B010R 5/10HP INPUT 230/460VAC 19A 3PH 50/60HZ OUTPUT 240/500VDC 20A DC FIELD 150/300VDC 10A SHORT CIRCUIT RATING 5000A M139750 WD30371-23 FOR 230V OPERATION. SEE I/M SERIAL NO. 1397-B01OR V001 WY MADE IN USA he technical power information on the nameplate should referenced to verify proper power application Firmware Version The manual covers firmware versions through 2.XX Publication 1397-5.- June, 2001

(系统自动生成,下载前可以参看下载内容)