派特莱下载FV-127JP 系列可录制存储电路板说明书.pdf派特莱下载FV-127JP 系列可录制

文件名称: 派特莱下载FV-127JP 系列可录制存储电路板说明书.pdf

所属分类: 其它

开发工具:

文件大小: 599kb

下载次数: 0

上传时间: 2019-10-11

提供者: weixin_********

下载 (599kb)

不能下载？报告错误

详细说明：派特莱下载FV-127JP 系列可录制存储电路板说明书pdf,高保真音质，可录制长时间的信息。 ·MP3格式音源，保证可长时间高保真音质的播放。 ·仅内部储存器最大可录制约8分钟长的音频信息。 ·附加使用外部储存器时最多可储存约240分钟长的音频信息。音频信息的读写功能 ·使用派特莱专业音源编辑软件“Playlist Editor”(免费软件)，不仅可以简单运行SD卡中的MP3编辑，也可将FV-127已储存的文件调出，写出SD卡中。自动减低音量功能 ·可通过接点输入信号自动控制音量的减低。3段减低（减低10分贝，减低20分贝，减低30分贝） 5种自Introduction Thank you for purchasing our Patlite Signal Voice MP3 Playback Circuit Board. Prior to installation, please read through this manual for proper installation and precautionary steps. In additon, please store this manual for future reference when performing maintenance, repairs or inspections After reviewing this manual, if there are any inquiries, please direct them to your PATLITE Sales Representative Markings in this book The bit rate of 64 kbit/s is given as the standard rate for the MP3 file. When the bit rates differ, reproduction time differs Optional SDv-128P should be used for the SD card. Using other SD cards is not guaranteed ( ka Refer to page 38 [(1)SD card(MP3 voice Format the SD card using the FAT16 protocol. The SD card cannot be recognized if it is formatted in any form other than FAT16 Copyrights Work that was recorded or copied from music CDs or other media used in public places may infringe upon copyrights and law enforcement may be imposed. When using a work that was recorded or copied from music CDs or other media be sure to obtain permission from the author Moreover, the copyright of the sound and music data which PATLITE Corporation distributes or sells belongs to our company. In addition, copyrights of audio/music data distributed or sold by PAtLItE Corporation belongs to PATLITE.It is strictly prohibited to copy/reprint whole or partial contents of audio/music data belonging to PATLITE Corporation, or to transfer/sell such material on computer networks etc. without the permission of the rightful holder Windows is a registered trademark of Microsoft Corporation of America, Japan and other countries e The PAtLITE Corporation is a member of the SD Card Association 1. Product Summary This product is a small sized mP3 file reproduction board which can also be used for factory automation(FA) Since MP3 is used as compressed data, it is possible to reproduce a high-quality sound voice message for an extended period of time. Moreover, the registered voice message can be rewritten freely. (a maximum of 127 messages can be registered) High Quality Sound/Long Playback Time The maximum voice message playback is a maximum of about 8 minutes Moreover, extende reproduction for a maximum of about 240 minutes can be done by using the optional Sd card Voice Message Rewrite-Export Function A voice message can be rewritten freely using the SD card The voice messages registered to this product can be read to the sd card Noise reduction Malfunction due to noise can be suppressed by the setup of input noise filters The noise reduction pin can reduce the effect of noise according to the environment Replay According to Application Five different modes can be selected for different playback modes With the control of an external signal, three levels of noise reduction can be made 3 2. Safety Precautions In order to prevent any damage to the user and other personnel or to assets, note the following warning is not taken into consideration and the product is not correctly usey e degree of danger or damage incurred when the The warning indications are divided into the following classes according to the △ Warning death or serious injury Indicates an immediately dangerous condition: failure to follow the instructions may lead to △ Caution Indicates a potentially dangerous condition: failure to follow the instructions may lead from slight to medium injury or to property or physical damage For safe application, observe the following △ Warning Ensure the power is in the correct tolerance for voltage supply. Failure to do so may result in malfunction or fire Do not modify or disassemble the product. Failure to do so may result in malfunction or fire During operation, the parts get hot, so do not touch the product and keep flammable things away. Failure to do so may result in serious burns or fire A Caution Before handling this product, be sure to discharge any static electricity by touching other metal parts to discharge static electricity. Moreover, don' t touch the parts or printed circuit board pattern that is not specified The parts on a board may be destroyed by static electricity, or the part leads may cause injury. This product incorporates a circuit board for exclusive use. Protect the board from conductive foreign substances, such as water and dust Dont allow tools etc to contact with the board. The possibility of short-circuiting and part damage may occur Make sure the power is off before wiring and mounting. The danger of burning the internal circuitry by short circuiting may occur. Don' t install the product in a location where vibrations exceed the specifications. Possible product damage or falling may occur This product is not guaranteed from failure produced by transportation, handling, natural disasters, etc or the disassembly and modification contrary to warnings and notes. Moreover, please avoid the use of this product outside the contents written in this book Please For safety purposes, be sure to carry out daily inspections and to perform preventative maintenance which can avoid down time and possible failure Don't control message reproduction by controlling the power source. Possible malfunction may occur Don't use in a location with corrosive gas present. Possible malfunction may occur Use this product only in environmental conditions indicated in this manual. Possible malfunction may occur in another environment 4 3 Part Names and function 5)Volume Volume 7)DIPSwitches (AUX) Speaker) 1)Installation Holes 4-(P3.5 2)Power Indicator LED(Green) 4)Glass 3)Status Indicator LED(Red) 10)Noise Filte Pin B 压Y+24 Noise filter 圈感感感圈 Pin a 9)FG 8)Installation 6)Terminal ole Holes Block 1. Installation Holes 4-(p3.5 Use the installation holes when mounting. 3r Refer to pg 9 [4. Installation]) 2. Power Indicator LED(Green The LED light turns on when power is applied 3. Status Condition Indicator LED(Red) See the table below for the flashing or non-flashing indication depending on the function ED Status Operation Off During standby or audio message playback On When transferring voice message When exporting voice message Flashing playback 3 Refer to pg 38 [9. Error Table]) 4. Glass Fuse Fuse to protect from overcurrent or overvoltage. Refer to the specifications below when replacing Glass Fuse: (p52x20 Rated Current: 1.0A Standard Fusion Type Replacement Part: Nippon Seisen Co, Ltd FBM 250V 1A/ Fujitsu Electric FGMB 250V A Caution Before replacing the fuse, disconnect the power source. The possibility of circuitry shorting or electrocution may occur. 5 5. Volume(Speaker, AUX Volume adjustment for the Speaker and aUX output is possible (1 Refer to pg 20 [6-1 Volume Adjustment]) 6. Terminal Bus Wiring terminal for individual Inputs and Outputs.(2 Refer to pg. 10 [5. Wiring]) 7. DIP Switches(Sets Functions Sets functions for playback mode, SD card operation, etc 13 Refer to pg. 22 [7. Mode Switch Settings]) 8. sD card slot Used for voice message rewriting voice message exporting and sd card permanent installation Refer to pg 31 [7-3. SD Card Operationl) SD Card slot Insertion When inserting, please push the SD Card in until a click is heard, and insert the sd card as indicated in the diagram below. To remove the SD Card, push in until a click is heard and release SD Card A Caut ion When you insert an SD card into the SD card slot, be careful of the direction. Also, don,' t push in SD card by force. Possible damage of the product and sd card may occur 9. FG Hole(Frame Ground Hole) In some cases, the earth grounding reduces noise. The Terminal bus is connected to the fg hole 10. Noise Filter Pin(A, B) Depending on the pin setting, incoming noise can be reduced Both pins are connected upon shipment, but by removing any of them may increase noise susceptibility Therefore, set the pins in accordance to the operating environment (5 Refer to pg. 13[(2) FG Terminal Wiring/Noise Reduction PinJ) 6 4. Installlation Use M3 screws and PCB spacers(not included )when installing the PC Board [] 144 134 4-M Recommended 鱼 Torque:0.3N·m ■■■ 90100 LanniN 6 ( Insersion Gap) FG Hole Ensure enough clearance is made for the SD Card (W: 24mm L: 32mm) to be inserted and removed Max 28 Recommended Spacer Size: 10mm (Use metal spacer when grounding via the FG Hole For dimensions( -g Refer to pg 38 [Outer Dimensions]) △ Caution M3 Screw Washer(φp8 mm or less) Spacer Ensure the insulation space is sufficient with a maximum length of 3mm for the lead wires coming from the PCB. If an insufficient space allows the lead wires to touch a conductive surface, a possibility of short-circuiting may occur Use an 8mm diameter washer. If a washer with a diameter over 8mm is used. contact with the pcB pattern may cause short-circuiting Use all 4 mounting holes when installing and use the recommended torque to prevent the screws from loosening and the product from unattaching 5. Wiring 5-1. Terminal Wiring and names COM CH Input Terminals COM CH1 CH2 CH3 CH4 CH5 CH6 CH7 STBSTOP CLR DEC1 OV /OL DEC2 SP- SP+ AUX-AUX+BUSY-BUSY+ 24V Input Terminal Output Terminals Power Terminals Name Function COM ommon connection for input terminals CH1-7 Channel selection terminal for audio messages. short to Com for the selected channel to playback message Two input modes"binary"and"bit"can be selected.(5p Refer to pg. 23 [7-1. Channel (CH) Terminal Input STB When in the Binary Mode, STB is used during playback. (Not applicable for the "Hold Playback "mode k Refer to pg. 30[(E Hold Playback) STOP Stops the message during playback CLR When used during the " memory playback"mode, the audio playback message is erased. For other modes the function is the same as the"stoP mode DEC1/OL, Depending on the input status, the speaker volume or AUX volume decreases DEC2 (B Refer to pg 21 [6-2. Reduction Function)) Speaker Terminal Connection(Note Polarity) t Refer to pg. 14 [(3)Speaker Output Terminal Wiring]) Amplifier Terminal Connection(Note Polarity AUX+ 1 Refer to pg. 15[4) AUX Output Terminal Wiring]) BUS BUSY+ (I Refer to pg. 17[5)BUSY Output Terminal Wiring/ arity) Output is produced during message playback(Note Pol 24V,0 Power Input Terminal. Connect DC24V only.(Note Polarity (r Refer to pg. 12[(1 Power Input Terminal Wiring) FG When connecting to earth ground (FG), under certain environments can reduce the effect of noise. The FG is connected internally 8 5-2. Wiring Wiring Example COM CH1 CH2 CH3 CH4 CH5 CH6 CH7 STB STOP CLR DEC1 DEC2 SP- SP+ AUX-AUX+BUSY-BUSY+ 24V OV FG VOL 8oOo×2 Speaker 8 十 DC24V Max 40VDC External AUX 十 GND Amplifier A Caution Do not connect the input connections to the power supply. Possible malfunction may occur When handling this product, please do so after discharging static electricity from on the body. Discharge the static electricity by touching other metal parts. In addition, do not touch parts in areas not specifed in this manual. Possible static electricity may destroy parts or the wire leads on the underside of the board may cause InJury Be sure to turn off the power before connecting wires. Possible short circuiting or burning-out of the internal circuitry may occu「 Please Ensure wiring is properly performed before connecting power. To prevent noise, make wire connections short and use shielded wiring. If installed where high voltage wiring is nearby, inductive noise may cause malfunctioning 9 5-2-1 Power Input Terminal Wiring Connect dC24V 24V0V Current Consumption For maximum load: About 520mA Inrush Current 9A A Caution Ensure wiring is properly performed before connecting power. If voltage is applied between OV and FG, it will cause a short circuit, and the power source will be destroyed OV FG Please Ensure voltage polarity is correct When used in a state where it is connected to the power source, please include a switch in which the power source can be easily cut for safety When using non-voltage contacts, such as a relay switch for power source wiring, please select in consideration of the rush current. If capacity is insufficient, it will cause welding of the contacts and malfunction Use the rated voltage supply when located in a quiet location to avoid white noise

(系统自动生成,下载前可以参看下载内容)