文件名称:
240-7kg,240-7kg传感器 产品简介.pdf
开发工具:
文件大小: 459kb
下载次数: 0
上传时间: 2019-10-09
详细说明:240-7kg,240-7kg传感器 产品简介pdf,240-7kg,240-7kg传感器 产品简介Model 240
Damped Load Cells
High Speed Performance with Wash Down Capability
APPLY| NG THE LO粪D
UNSTABLE READINGS
he load must be applied via the wearing surface
Unstable readings from his type of load cell can be
which is uppermost on the load applicator. Both
caused by aty ef the following
holes must be used, evenly torqued to 16Nm (12
bMi so that the load is evenly distribued
1)Mechanical interference beteen the loadin
nechanism and the frame of the machine In
h is usual to use a fiat bar or some gher load
particular where product buids up or dirt is trapped
spreading member between the applicator and the
between the load pillar and the model 240 body.
wtgh platform, table or live superstructure. The
ting secton and the substructure, must be rigid
2) The transpartation grub screw in the load cap
otherwise the latter will oscillate and superimpose
Pas not been opened or has vibrated back down
on the load cell output, depending on the frequeney
nto the closed position
nd ampltude generated. The supporting member
must te flat
3) The sin;ered bonze breather filters located on
the sides of the load cap are blocked with Gontami-
The load shoukd be transported on to the weigh
n善t:faw阳 mperatures ap
platform in such a way that it creates the minimum
plication where the filters have been blocked by
disturbance. the ond transverse司e05即e
ice. If the application is in a corrosive atmospher
platform, it should, if poss ble, avoid knocking the
platform edge (ue. no step): If the load is lowered
chemicals. the filers can also corrode and became
on to the platform it should be a contralled place
blocked, Plastic filters can be fitted for use in ag-
ment: not a dropped load. For aptimum perform
passive envionments or a speaal version of the
ance the line of action of the applied load shguld
nadel 24D with remote breathin
ng be supplied on
act as near as possible to create line of the load
cell-in both horizontal planes to minimize eope
quest for use in high humid ty. low te mpe rature or
d
facty efects
ablins吧
EFFECT OF TEMPERATURE
SEALING
The preceding response carves reflect a typical
The model 240 is deal for wash down condit ens in
lemperature will affect the viscosty of the dam
the food industry and other demand ing environ-
ments
Tuia and consequently the setlling time of the
A dual combination af a wash down shroud and
d aphragin is designed to prevent the ingress of
water allowing the load ce l o breathe, in order to
INSTRUMENTATION
overcome variations in barometric pressure
The load cell is essentally a strain gauge device of
Wheatstone Bridge configuration hawing input
output signals in milli-voRts. Normally, standard
Protection is designed to pass a 50 day humidity
cycle at 957 R.H. and the unit is sealed to IP66
load cell weighing equipment instruments will
BS 5490 EC 529) Cert No2039
match
satisfactory, but note that the load cell output is
offset dependant upan platon ar container
PACKAGING, TRANSPORT AND STORAGE
weight. The cable should be clamped in position
The laad cell is packed in a cardboard heusing for
and should not be continuously flexing
dispatch and should be stored in its original
Note, the mode 240 is supplied in six wire
packaging if pessible. It is essential to store the
configuration and where possible this should be
load cell upright with the transportation screw tight
tailly ut lized
(see salla tion sheen, Storage temperatures
shouk not exoeed-15C1o+45C, Never carry the
nodel 240 by the cable
Model 240
WSHAY
Tedea-Huntleigh
PRECSION
GEOUP
Fluid-Damped single-Point Load Cell
SPECIFICATIONS
PARAMETE
SALUE
Rated capaci一Rc.[mad
sT,021,2030
0ML accur
Maximum no of intervals inl
IrsO
MiXtuM ayabe
Radu中山t-R
mWy
=mve
Zaro raturn, 30 min.
0,3
05
ty df appfedlo
Total error
0Du
Q015
± rued outpur
Temparature effect on zero
± 4 drawed opitc
Tamparaturo affact on output
QNd
Na
00010
±畅 d rabs ouput/C
orature runge compensated
101440
-40TE-FLU
形可R
r叫Yhad
%of R.C.
Exc tation, recommanded
danne
aton resits
emirebraided.pclyuethne,sifconegelimpregnution
standard
Construction
Parted med stee
Environmental protaction
EoA titIon
2 and B kg are nct approved by NTEP OML
S酣bhl
Al specifications subject to ohange wihou notice.
RING SCHEMATIC D』AGRA
*HPUT Reai
EsE归
配P山T(通
L
wPW加
古wwp中EdL心om
Technica cotact in Americas k us BimnA-EAL
Document o. 12r0
Raisin: 31-u-201:2
以上内容技术参数以《OML60号国际建议》92年版为基础,最新具体变化可查看《』G669
12 transcel!广州锐拓传感器事业部检定规程》
(系统自动生成,下载前可以参看下载内容)
下载文件列表
相关说明
- 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
- 本站是交换下载平台,提供交流渠道,下载内容来自于网络,除下载问题外,其它问题请自行百度。
- 本站已设置防盗链,请勿用迅雷、QQ旋风等多线程下载软件下载资源,下载后用WinRAR最新版进行解压.
- 如果您发现内容无法下载,请稍后再次尝试;或者到消费记录里找到下载记录反馈给我们.
- 下载后发现下载的内容跟说明不相乎,请到消费记录里找到下载记录反馈给我们,经确认后退回积分.
- 如下载前有疑问,可以通过点击"提供者"的名字,查看对方的联系方式,联系对方咨询.