文件名称:
240-2kg 240-2kg称重传感器 产品简介.pdf
开发工具:
文件大小: 461kb
下载次数: 0
上传时间: 2019-10-09
详细说明:240-2kg 240-2kg称重传感器 产品简介pdf,240-2kg 240-2kg称重传感器 产品简介Model 240
Damped Load Cells
High Speed Performance with Wash Down Capability
APPLYING THE LO粪D
UNSTABLE READINGS
The load must be applied via the bearing surface
Unsta ble readings from this type of load cell can be
which is uppermost on the load applicator. Both
eased by any et the following
holes must be used evenly torqued to 16Nm (12
用 that the 4as棒 evenly distribute
1)Mechanical interference betwveen the loading
mechanism and the frame of the mach ne. In
it is usual to use a fat bar or some o her load
particular where product builds up or dirt is trapped
spreading member between the applicator and the
between the load pillar and the model 240 bod
weigh platform, table ar live superstructure. The
mating section and the substructure, must be rigid
otherwise the latter will oscillate and superimpose
2) The transpartation grub scew in the load cap
has not been opened or has vibrated back down
on the load cell output, depending on the frequency
to the closed pasition
and amplitude generated. The supporting membet
must he flat
3) The sintered bronze breather filters located on
the sies of the load cap are blocked with eontami
The load should be transported on to the weigh
轴uqh得s: Or in a low temperature
platform in such a way that it creates the minimun
plication where the filters hawe been blocked by
disturbance. If the lod trans verses acr ass the
platform, it should, if poss ble, avoid knocking the
or the machine is washed down with aggress
ice. If the application is in a corrosive atmosphe
platform edge (ie. no step). If the load is lowered
chemicals. the filters can also corrode and become
on to the platform it should be a controlled place
blocked. Plastic filters can be fisted for use in ag
ance the line of action of the applied load should
gressive environments or a specal version of the
model 240 with remote beathing be supplied an
act as near as possible to create line of the loac
request for use in high humidity, low temperature or
cell in both horizontal planes to minimize eccen
dusty
teaty efrects
EFFECT OF TEMPERATURE
SEALING
The preceding response curves feflect a typical
The model 240 is Heal for wash doyin cand tons in
ambient temperatare of 20oC, Variations in
temperature will alect the viscosty o! the damping
the food industry and other demanding environ
ments
Iuid and consequently the settling time of the load
cell
a dual combination of a wash down shroud and
d aphragm is designed to prevent the ingress of
water allowing the load cell to breathe, in order to
INSTRUMENTATION
overcome variations in barometric pressure
The load cell is essentally a strain gauge device of
Wheatstone Bridge configuration having input/
Protection is designed to pass a 50 day humidity
output signals in milli-volts, Nammaly. standarc
load. cell weighing equipment instruments will
cycle at 95%R H. and the unit is sealed to IP66
(BS 5490 IEC 529)Cert No 2039
match
satisfaconly. but note that the load cell output is
offset dependant upan platform ar cotainer
PACKAGING, TRANSPORT AND STORAGE
weight. The cable should be clamped in position
The load cell is packed in a cardboard housing for
and should not be contimuously flexing
d spatch and should be stored i its original
Note, the model 240 is supplied in six wire
packaging if pessible. It is essential to store the
configuration and where possible this should be
load cell upright with the transpartation screw tight
lly utilized
(see installation sheet), Storage temperatures
shouk not exceed-15C to +45C, Never carry the
model 240 by the cable
Model 240
Damped Load Cells
GRADE
UNITS
ated Capacitive
23.5F7.10.15.2015.71020.30
30.50
Rated Opul
20±10%
tal Error
0050
0025
D.020
土% I Applied LA3d
eR也 rn afer30rins
0075
0.15
±% Applied Le
NA
D0010
6 of Applied LoadI
Temperature Effect: On Zero
. NA
NA
0.0026 of Rated Load OrpulI'C
Eccentric Loadin
t% of Rated outs吨t
Zero Balance
贴 of Rated output
erature Range: operating
30t0+70
啦们时包 te Ranu Compensated
Safe Overload
150
T of Rated Capacity
d Raled Capacty
tilation Recoin mended
Vdis AC or DC
宝3 on. Maximian
5
Volts AC or DC
415±15
350±
isulation Impedance
1000
04
ka
Coated steel or stainless steel
wironmental Protection
ble
E Meters( Standardl. 6 wire Polyurethane
Jacket Dual Floating screen
aortas
OIML R60 NTEP
叫 EIror-Aodd touR*s山d时o%山 on-LCwn山nc面
Outline Dimensions All Capacities (in mm
aMounting Holes
ME-100r14-2oUNC
585
4 Mounting Holes
990 Er
中
Optional Wash dawn shroud o ss
Wiring schematic Diagram
e(upi FodI
-input (Black
以上内容技术参数以《OML60号国际建议》92年版为基础,最新具体变化可查看《』G669
12 transcel!广州锐拓传感器事业部检定规程》
(系统自动生成,下载前可以参看下载内容)
下载文件列表
相关说明
- 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
- 本站是交换下载平台,提供交流渠道,下载内容来自于网络,除下载问题外,其它问题请自行百度。
- 本站已设置防盗链,请勿用迅雷、QQ旋风等多线程下载软件下载资源,下载后用WinRAR最新版进行解压.
- 如果您发现内容无法下载,请稍后再次尝试;或者到消费记录里找到下载记录反馈给我们.
- 下载后发现下载的内容跟说明不相乎,请到消费记录里找到下载记录反馈给我们,经确认后退回积分.
- 如下载前有疑问,可以通过点击"提供者"的名字,查看对方的联系方式,联系对方咨询.