台达可编程控制器（PLC）DVP04AD-E2安装说明.pdf台达可编程控制器（PLC）DVP04A

文件名称: 台达可编程控制器（PLC）DVP04AD-E2安装说明.pdf

所属分类: 其它

开发工具:

文件大小: 774kb

下载次数: 0

上传时间: 2019-09-14

提供者: weixin_********

下载 (774kb)

不能下载？报告错误

详细说明：台达可编程控制器（PLC）DVP04AD-E2安装说明pdf,台达可编程控制器（PLC）DVP04AD-E2安装说明：DVP04AD-E2 模拟量输入模块接受外部4 点模拟量信号输入 (电压或电流皆可)，将之转换成16 位的数字量信号。使用者可经由配线选择电压输入或电流输入。并可透过主机以FROM / TO 指令来读写模块内数据，或者以MOV 指令直接读取对应通道平均值EXternal Wiring Vol tage inpu CH1 CH 1 1Mn A V11-H d cable·1 Current input CH4 Shielded cable.1 FE TErminal of power module +15V System Converter -15V Grounding(100Q or less) · Passive-type Voltage input 1MQ Current input CH4 250g CH4 Shielded cable.1( TErminal of DC/DC Converte Grounding(100Q less) I Figure 4] Note 1 When performing analog input, please isolate other power wirings Note 2: When the A/D module is connected to current signals, make sure you short-circuit"V+ and Note 3: If the noise is too significant, please connect FE to the grounding terminal. Note 4: Please connect the O terminal on both the power module and A/D module to the system earth Note 5: If the ripples at the loaded input terminal are too significant that causes noise interference on the wiring, connect the wiring to 0. 1-0.47uF 25V capacitor lo Terminal layout 「Ⅳ1+1+WTFEⅣ2+I2+V2IFE3+3+Ⅳ3TE DVP04AD-E2(4A/) 240V线FEM4+■4+M4FE Electrical Specifications Analog / Digital module(04A/D) Power supply voltage 24VDC(20.4VDC-28.8VDC)(-15%++20%) 2 Analog /Digital module(04A/D) Max rated power 1W, supplied by external power source Connector European standard removable terminal block(Pin pitch: 5mm) Operation: 0.C-55C(temp. ),50-95%(humidity), Pollution degree2 emperature Storage:-25°c-70°c(temp.),5-95%( humidity) Vibration/shock International standards: IEC61131-2, IEC 68-2-6(TEST Fc) EC61131-2&EC682-27( TEST Ea) The modules are numbered from 0 to 7 automatically by thei Series connection to distance from MPU. Max. 8 modules are allowed to connect to MPU DVP-PLC MPU and will not occupy any digital l/o points a Functions Specifications Current input Analog input channel 4 channels /each module Range of analog input +10V ±20mA ~20mA 4~20mA Range of digital ±32.00132000±32000-320000~32,00 Max /Min. range of 32,384 32384±32384 384~+32384|-384~+32,384 Hardware Resolution 14 bits 14 bits 14 bits 13 bits Input impedance 1MQ 250Q Range of absolute input| +15V Overall accuracy ±0.5% when in full scale(25°C,77F) ±1% when in full scale within the range of0-55°C(32-131°F) Response time 400 us/each channel Digital data format 2s complement of 16 bits Average function Supported. Available for setting up sampling range in CR#8 CR#11. Range: K1 -K100 Self-diagnosis Upper and lower bound detection in all channels Optical coupler isolation between digital circuits and analog circuits No isolation among analog channels 500VDC between digital circuits and Ground solation method 500VDC between analog circuits and Ground 500VDC between analog circuits and digital circuits 500VDC between 24VDC and ground Control Register CR# Attrib. Register name Explanation #oor Model name by DVP04AD-E2 model code = H0080 #1oR Firmware version Display the current firmware version in hex Input mode: Default= H0000 #2 O R/ CH1 input mode setting Take CH1 for example (H0000 Voltage input (+10 #3 O RN CH2 input mode setting Mode 1(H0001): Voltage input(+5V) Mode 2(H0002): Voltage input(0-+10v) #4 O R/ CH3 input mode setting Mode 3(H0003): Voltage input (0-+5v) Mode 4(H0004 ): Current input (+20mA) Mode 5(H0005): Current input (0-+20mA #5 O R/ CH4 input mode setter Mode 6(H0006 ): Current input (+4-+20mA) Mode-1(H'FFFF) 1 3 CR# Attrib. Register name Explanation OR/ CH1 sampling range #9 OR/I CH2 sampling range Set sampling range in CH1 - CH4 Range= K1 -K10 #10 O R/ CH3 sampling range Default= K10 R/ CH4 sampling range #12X R CH1 average input value #13XR CH2 average input value R CH3 average input value Average value of input signals at CH1 -CH4 #15×R|cH4 average input value #20 R CH1 present input value CH2 present input value Present value of input signals at CH1 - CH4 R CH3 present input value #23X R CH4 present input value #28 o R/ Adjusted Offset value of CH1 Set the adjusted Offset value of CH1-CH4 #29 o R/ Adjusted Offset value of CH2 Default KO Definition of offset in DVP04AD-E2 #30 R/ Adjusted Offset value of CH3 The corresponding voltage (current)inpu #31 o R/ Adjusted Offset value of CH4 value when the digital output value=0 #34 JO/W Adjusted Gain value of CH1 set the adjusted Gain value in CH1-CH4 #35 O R/ Adjusted Gain value of CH2 Default=K16,000 Definition of gain in dvPo4AD-e2 #36 o R/ Adjusted Gain value of CH3 The #37 OR/W Adjusted Gain value of CH4 value when the digital output value=16,000 #40 o R/ Function: Set value changing Prohibit set value changing in CH1-CH4 prohibited Default= hooo0 #41XR ction Save all the set Save all the set values, Default =H0000 Function: Return to default Set all values to default setting, Default #42XR setting H0000 #43 XR Error status Register for storing all error status. Refer to table of error status for more information Function: Enable/Disable limit Enable/Disable the upper and lower bound #100 o R/ detection detection function Default= H0000 #101XR/ Upper and lower bound status Display the upper and lower bound value Default=H0000 #102 OR/ Set value of CH1 upper bound #103 oR/W Set value of CH2 upper bound set value of CH1-CH4 upper bound Defau #104 R/ Set value of CH3 upper bound=K32000 #105 O/ Set value of CH4 upper bound #108 o R/ Set value of CH1 lower bound #109 R/ Set value of CH2 lower bound set value of CH1-CH4 lower bound. Default #110 o R/ Set value of CH3 lower bound=K-32000 #111 o R/ Set value of CH4 lower bound Symbols O: When CR#4 1 is set to h 5678 the set value of cr will be saved X: set value will not be saved R: able to read data by using from instruction W: able to write data by using To instruction 4 CR#43: Error status value. See the table below Description bito K1(H1) Power supply error bit6 K64(H40) CHA Conversion error bit1 K2(H2)Hardware error bit9 K512(H'0200) Mode setting error bit2 K4(H4) Upper/lower bound error bit 10 K1024(H 0400)Sampling range error bit3 K8(H8)CH1 Conversion error bit11 K2048(H 0800)upper /lower bound Set value changi bit4 K16(H10) CH2 Conversion error bit 12 K4096(H 1000)prohibited Communication bit5 K32(H 20) CH3 Conversion error bit 13 K8192(H2000) breakdown on next /Note: Each error status is determined by the corresponding bit(b0-b13)and there may be more than 2 errors occurring at the same time 0= normal. =error a Explanation on Special Registers D9900-D9999 When DVP-ES2 MPU is connected with modules, registers D9900-D9999 will be reserved for storing values from modules. You can apply MOV instruction to operate values in D9900-D9999 When DVP-ES2 MPU is connected with DVP04AD-E2, the configuration of special egisters is as below: Module Module Module Module Module Module Module ModuleDescription #2 #4 # D1320D1321D1322D1323D1324D1325D1326D1327Moe D990D9910D9920D9930D9940D9950D9960D9970/CH1 D9901D991109921099109941099510986109971|cH2 average Input value D9902 D9912 D9922 D9932 D9942 D9952 D9962 D9972 CH3 average D993D9913D993D993D9943D953D993|D9973/cH4 average input value Note 1: D9900-D9999 are average input values of CHI- CH4 and the sampling range is Kl-K100 When the sampling range is set to Kl, the values displayed in D9900-D9999 are current values You can use: 1. ES AlO Configuration Function of wPLSoft or 2 FROM/TO instructions(CR#8 CR#1l) to set the sampling range as KI Adjust A/D Conversion Curve Users can t the conversion curves according to the actual needs by changing the Offset value( CR#28-CR#31)and Gain value(CR#34 -CR#37) Gain: The corresponding voltage/current input value when the digital output value 16,000 Offset: The corresponding voltage/current input value when the digital output value =0 Equation for voltage input Modeo /Mode2: 0. 3125mV= 20V/64,000=10V/32, 000 y=16000090 Y=D put, X=Voltage Equation for voltage input Mode 1 /Mode3: 0. 15625mV= 10V/64,000=5V/32,000 5 y=1600(0 57)3200%e|/aim-O/en) Equation for current input Mode4 /Mode5: 0.625uA= 40mA/64,000= 20mA/32, 000 Y=16000 3(03000m0) Y=Digital output, X=Current input Equation for current input Mode6: 0.5uA=16mA/32, 000 Adopt the Equation of current input Mode4/Mode5, substitute Gain for 19200 (12mA)and Offset for 6400(4mA Y=16000 20m×3200640009200-6400 Y=Digital output, XCurrent input ·Mode1 +32384 32384 +32000 Digital output +16000 output +16000 10v Offset Gain 6000 Mode o of cR#2 cR#5 -10V-+10 V, Gain=5V(16,000) t=0v(0) Mode 1 of CR#2- cR#5 5V-+5 V, Gain=25V(16.000), Range of digital conversion-32, 000-+32,000 Max /Min range of digital -32,384~+32,384 de 2 Mode 3: 384 +32384 +32000 Digita Digital output+16000 output+16000 Gain 2.5V Offset Voltage input Mode 2 of CR#2-CR#5OV-+10V, Gain=5V(16,000), Offset=0V(0) Mode 3 of cr#2- crtt 0V-+5V,Gain=25V(16,000), Offset=0V(0) Range of digital conversion 0-+32,000 Max /Min. range of digital 384~+32.384 inversIo 6 +32384 32000 +16000 20mA 20mA Offset Gain 16000 Mode 4 of cr#2- cr#5 20mA-+20mA, Gain= 10mA(16, 000), Offset = OmA(O) Range of digital conversion-32, 000-+32,000 Max /Min range of digital -32,384~+32,384 32384 32000 +16000 upu +1600 10mA 4mA 12mA 20mA Offset Current input Current input Mode 5 of CR#2-CR#50mA-+20mA, Gain= 10mA(16,000), Offset=OmA(O) Mode 6 of cr#2- cr#5 +4mA~+20mA.Gain=12mA(19200), Offset=4mA(6,400) Range of digital conversio 0-+32,000 Max /Min range of digital 384~+32,384 conversion 7 感謝您採用台達DVP系列產品DP04AD-E2類比輸入模組接受外部4點類比信號輸入 (電壓或電流皆可)·將之轉換成16位元之數位信號。使用者可經由巸線選擇電壓輸入或電流輸入。並可透過主機以FROM/TO指合來讀寫模粗內資料·或者以MOV指命值接讀取對應通道平均值(請參閱D9900~D999特殊暫存器使用說明) κ本安裝說明書提供給使用者鼋氣規格丶功能規格丶安裝配湶之相關注意事項。其他詳沺之程式設計及指合說明請見DνPES2操作手冊【模粗篇】·選購之周邊裝置詳粑說明請見該產品隨機安裝說明書 κ本機焉開放型(○ PEN TYPE)機殼·因此使用者使用本機時·必須將之安裝於具防壟丶防潮及免於鼋擊衝墼意外之外殼配線箱內。另必須具備保護措施(如:特殊之工具或鑰匙扌可打開)防止非稚護人員操作或意外衝擊本體,造成危險及損壞 κ交流輸入電源不可連接於輸入岀信號端·否則可能造成嚴重損壞·請在上電之前再次確記電源配線。請勿在上電時觸摸任何端子。本體上之接地端子③務必正確的接地可提高產品抗稚訊能力產品外觀尺寸與部位介紹脫落式翰出入端子機型號源、A→>D及錯誤指示登 N軌棺 /O檩祖固定扣翰出/人端子涓虢接固定孔 ·詳粑尺寸區請參閱英文版頁碼1之 Figure2,單位:mm。外部配線主動式百翰入 CH1 509 CH1 4+h 4+ 509 CH4 轉换器接地(接地阻抗1004以下) 被動式輪入 CH1 CH1 5 隔離湶*1 FE CH4 隔離湶*1 授至源模之端 +15V DC/DC 地区241 轉换器 15V 接地(接地阻抗1009以下) 註1:類比輸入請與其他電源線隔離註2:如果連接電流訊號時·Ⅵ+及卜端子詩務必短路。註3:如果雜訊過大詩將FE及接地端子連接註4:將電源槙祖之③端及AD模擬量信號輸入模塊之③端連接到系锍接地點,再將系锍接點作第三種接地或接到配電箱之機殼上註5∶如果輸入電歴有漣波造成配線受雜訊干擾時·請連接0.1~0.47μF25V之電容輸入/輸出端子台配置請參閱英文版頁碼2之端子配置圄’在此語言版本省略說明電氣規格類比位模組(04AD 鼋源電壓 24vDC(20.4VDC~288vDC)(-15%~+20%) 額定最大消耗功率,由外部重源供應。連接方式脫落式歐式端子座(端點距離:5mm) 操作:0°C~55°C(温度),50~95%(濕度)污染等級2 操作儲存環境儲存:-25°C~70°C(溫度)·5~95%(濕度) 耐振動/衝擊國際標凖規範旧C61131-2·EC68-2-6( TEST FC)/EC61131-2&EC 68-2-27(TEST Ea) 與 DVP-PLC主機串模祖編號以靠近主機之順序自動號由0到7,最大可連接8台且不佔接說明用數位WO點數。功能規格類比擻位模電壓輸入電流輸入颊比訊號输又通道4通道/台類比輸入範圍 ±5V ±20mA 0~20mA 4~20m 位资料範圍 ±32000±32000±3200 數位料範圍極限值|±32,384 32.384 ±32.384 384~+32,384-384~+32,384 硬體解析度 14 bits 14 bits 14 bits 13 bits 13 bits 輸入阻抗對輸入範圍 15V ±32mA 9

(系统自动生成,下载前可以参看下载内容)