三菱 FX-10DM-E用户手册.pdf三菱 FX-10DM-E用户手册pdf,This secti

文件名称: 三菱 FX-10DM-E用户手册.pdf

所属分类: 其它

开发工具:

文件大小: 1mb

下载次数: 0

上传时间: 2019-09-14

提供者: weixin_********

下载 (1mb)

不能下载？报告错误

详细说明：三菱 FX-10DM-E用户手册pdf,This section describes the product configuration and the system configuration of the FX- 10DM-E (hereafter referred to as "10DM"). Make sure that all accessories are included in the package before using the 10DM. (Refer to Paragraph 1.5.)FX-10DM-E DISPLAY MODULE Notification of CE marking c The following products have shown compliance through direct testing( to the identified stan- dards and design analysis(forming a technical construction file to the european Directive for Electromagnetic Compatibility(89 /336/EEC)When used as directed by the appropriate docu mentation Type: Programmable Controller(open type Equipment Models: MELSEC DM series products, identified here, manufactured from January 1st, 2002 FX-10DM-E (For this product see note under and over the page Standard Remark EN50081-2:1993 Electromagnetic compatibility Compliance with all relevant aspects of the standard Generic emission standard Industrial (Radiated Emissions and Mains Terminal voltage environment Emissions) EN61131-2:1994+A11:1996+A12:2000 Programmable controllers Compliance with all relevant aspects of the standard -Equipment requirement and tests (RF Immunity, Burst Transients and ESD) For more details please contact the local Mitsubishi Electric sales site AMITSUBISHI FX-10DM-E DISPLAY MODULE Notes Regarding the use of DM Units General notes on the use of communication cables Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise. Therefore, when installing any communication cables care should always be taken with the routing and location of those cables. The DM units identified on the previous page are compliant with the EMC requirement when the following communication cables are used able 0.1 DM Unit New cables Existing Cables User Made cables This cable need to be independently From version a FX-20P-CAB0 modified tested by the user to demonstrate EMc FX-10DM-E(JY309C24571A)of the FX-20P-CABO/EN as shown in EX. compatibility when they are used with Mitsubishi dM units and programma ble Controllers When using the FX-20P-CABO/EN cable the Earth Strap must be connected to a suitable earth oint EX. 1 FX-20P-CAB0 E=Additional earth strap connected to the cables 40mm shield. Free end of the earth strap must be connected to an earth point F= Ferrite core Ex. Tokin-ESD-R-14s or similar Programmable Controller DM units AMITSUBISHI FX-10DM-E DISPLAY MODULE FX-1ODM-E DISPLAY MODULE USER'S MANUAL Manual number JY992D86401 Manual revision :f Date September 2008 AMITSUBISHI FX-10DM-E DISPLAY MODULE AMITSUBISHI FX-10DM-E DISPLAY MODULE Guidelines for the safety of the User and protection of the dIsPLAY MODULE FX-10DM-E This manual provides information for the use of the diSPLAY MODULE FX-1ODM-EThe manual has been written to be used by trained and competent personnel. the definition of such a person or persons is as follows a) Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual, should be of a competent nature, trained and qualified to the local and national standards required to fulfill that role. These engineers should be fully aware of all aspects of safety with regards to automated equipment b)Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the completed product. This includes being completely familiar with all associated documentation for said product. All maintenance should be carried out in accordance with established safety practices c)All operators of the completed equipment (see Note) should be trained to use this product in a safe manner in compliance to established safety practices. The operators should also be familiar with documentation which is associated with the actual operation of the completed equipment Note The term 'completed equipment refe a third party constructed device which contains or uses the product associated with this manual AMITSUBISHI FX-10DM-E DISPLAY MODULE Notes on the Symbols Used in this Manual At various times throughout this manual certain symbols will be used to highlight points which are intended to ensure the users personal safety and protect the integrity of equipment Whenever any of the following symbols are encountered its associated note must be read and understood. Each of the symbols used will now be listed with a brief description of its meaning Hardware Warnings A 1) Indicates that the identified danger WILL cause phy sical and property damage A 2) Indicates that the identified danger could POssiBLy cause physical and property damage STOP 3)Indicates a point of further interest or further explanation Software Warnings 4)Indicates special care must be taken when using this element of software ①国 Indicates a special point which the user of the associate software element should be aware 6)Indicates a point of interest or further explanation AMITSUBISHI FX-10DM-E DISPLAY MODULE Under no circumstances will Mitsubishi Electric be liable responsible for any consequential damage that may arise as a result of the installation or use of this equipment All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples Please contact a Mitsubishi Electric distributor for more information concerning applications in life critical situations or high reliability AMITSUBISHI FX-10DM-E DISPLAY MODULE AMITSUBISHI

(系统自动生成,下载前可以参看下载内容)