文件名称:
伊顿 变频器MVX9000说明书.pdf
开发工具:
文件大小: 3mb
下载次数: 0
上传时间: 2019-09-14
详细说明:伊顿 变频器MVX9000说明书pdf,For the best results with the MVX9000 inverter, carefully read this manual and all of the warning labels attached to the inverter before installing and operating it, and follow the instructions exactly. Keep this manual handy for quick reference.Safety Instructions
arnings, Notes and cautions
A
Always read this manual thoroughly before using MvX9000 Ac
Motor drives
△
HIGH VOLTAGE!
Be sure to ground the unit. otherwise, there is danger of
electric shock and/or fire
A
HIGH VOLTAGE
Wiring work shall be carried out only by qualified personnel
Otherwise, there is a danger of electric shock or fire
A
WARNINGH
AC input power must be disconnected before any
maintenance, Do not connect or disconnect wires and
connectors while power is applied to the circuit. Maintenance
must be performed by qualified technicians
△
WARNING
a hazardous voltage charge may still remain in the dc-link
capacitor even if the power has been turned off. To avoid
personal injury, do not remove the cover of the ac drive until
all"DISPLAY LED lights on the digital keypad are off. Please
note that there are live components exposed within the ac
drives. Do not touch these live parts.
WARNING
The ac drive may be destroyed beyond repair if incorrect
cables are connected to the input/output terminals. Never
connect the Ac drive output terminals T1, T2, and T3 directly to
the ac main circuit power supply
A
WARNING!
Hazardous voltage
Before opening the ac drive covers
Disconnect all power to the Ac drive
Wait five minutes for dc bus capacitors discharge.
Any Electrical or mechanical modification to this equipment
without prior written consent of Eaton Cutler- Hammer will void
all warranties and may result in a safety hazard in addition to
voiding the UL listing.
Cutler-Hammer mvX9000 User manual
Safety Instructions
A
WARNING!
Wait at least 2 minutes after all display lamps have gone out
and then confirm that the capacitors have fully discharged by
measuring the voltage between B1 and Ground using a multi
meter set to measure dc
WARNING
Opening the Drive voids the warranty!
WARNING!
Make sure that all screws are tightened to the proper torque
rating shown in Table 3-2
WARNINGH
This equipment should be installed, adjusted, and serviced by
qualified electrical maintenance personnel familiar with the
construction and operation of the equipment and the hazards
involved. Failure to observe this precaution could result in
bodily injury.
WARNING
Use 75C Cu wire only"or equivalent.
WARNING
Suitable for use on a circuit capable of delivering not more
than 5,000 rms symmetrical amperes, 240 V maximum.
WARNING!
Suitable for use on a circuit capable of delivering not more
than 5,000 rms symmetrical amperes, 480 V maximum.
A
WARNING!
Disconnect AC power before proceeding
CAUTION!
There are highly sensitive Mos components on the printed
circuit boards. These components are especially sensitive to
static electricity. To avoid damage to these components, do
not touch these components or the circuit boards with metal
objects or your bare hands
Cutler-Hammer MvX9000 User Manual
H
Safety Instructions
CAUTIONH
Ground the MvX9000 using the ground terminal. The
grounding method must comply with the laws of the country
where the ac drive is to be installed. Refer to the Basic Wiring
Diagram in Chapter 3
CAUTIONH
△△
Do not connect the ac power to the t1, T2, t3 terminals, it will
damage the ac drive
CAUTIONI
Be sure to install the unit on flame-resistant material such as a
steel plate. Otherwise, there is the danger of fire
A
CAUTION
Be sure to install the unit on a perpendicular wall which is not
subject to vibration. Otherwise, it may fall and cause injury to
personnel.
A
CAUTION!
Be sure not to let the foreign matter enter vent openings in the
inverter housing, such as wire clippings, spatter from welding
metal shavings, dust, etc. Otherwise, there is the danger of fire.
A
CAUTION!
Be sure not to install or operate an inverter which is damaged
or has missing parts. otherwise, it may cause injury to
personnel
A
CAUTION!
Be sure to install the inverter in a well-ventilated room which
does not have direct exposure to sunlight, a tendency for high
temperature, high humidity or dew condensation high levels of
dust, corrosive gas, explosive gas, inflammable gas,
grinding-fluid mist, salt damage, etc. Otherwise, there is the
danger of fire
A
CAUTIONH
Be sure that the input voltage matches the inverter
specifications
Single/Three phase 200 to 240 50/60 Hz(up to 2.2k/W)
Three phase 200 to 230 V 50/60 Hzabove 22kw)
Three phase 380 to 460 50/60 Hz
Cutler-Hammer mvX9000 User manual
Safety Instructions
A
CAUTIONH
Power Input Power Output
Be sure not to connect an ac power
injury and/or fire.
Note
L1 L2, L3: Three-phase 200 to 230V 50/60 Hz
Three-phase 380 to 460V 50160 Hz
Any two inputs: Single-phase 200 to 240V 50/60 Hz
A
CAUTION
The operation of the inverter can be easily changed from low
speed to high speed Be sure to check the capability and
limitations of the motor and machine before operating the
inverter. Otherwise, there is the danger of injury.
CAUTION!
If you operate a motor at a frequency higher than the inverter
standard default setting (50Hz/60Hz), be sure to check the
motor and machine specifications with the respective
manufacturer. Only operate the motor at elevated frequencies
after getting their approval. otherwise, there is the danger of
equipment damage
Cutler-Hammer MvX9000 User manual
Safety Instructions
This page intentionally left blank
Cutler-Hammer mvX9000 User manual
Table of contents
Safety Instructions
Safety Messages…
Definitions and symbols
,,,
Hazardous high voltage
1面
Warnings, Notes and Cautions
ab| e of contents,…,nn…
Chapter1- Introduction……………,…,……………
Chapter 2 -Overview of the MvX9000 Drive
2-1
Receiving and Inspection
2-1
Digital Keypad Operation
.2-3
Chapter 3 -Storage and Installation
3-1
Storage
3-1
Environment
3-1
Mounting Area
3-2
Wiring
3-3
Applicable Codes
3-3
Basic Wiring diagram.…
External Wiring…
1
3-5
Control Terminal Wiring(Factory Settings)
3-6
Main Circuit Wiring
3-7
Motor Operation precautions
3-9
Chapter 4 -Start-up Procedures
…4-1
Step-by-Step Installation
4-1
Mounting Location
4-1
Inverter Mounting.…
4-3
Wiring preparation
国
4-4
Wiring the Inverter to Incoming Power.
4-8
ing the Motor to the Inverter Output
4-8
Powerup Test
4-9
Chapter 5 -Descriptions of Parameter Settings
Parameter Groups.
.5-3
Cutler-Hammer MvX9000 User Manual
Table of contents
Group 20--Basic Grouping(Quick Start
5-4
Group 30- Inputs
.5-6
Group40— Outputs
∴25-24
Group50- AC Drive Control….…
5-28
Group 60-Motor Control
5-45
Group 70- Protective Functions
5-49
Group80— Display
5-54
Group 90--Communications
5-58
Chapter6- Maintenance and Ins pection…,,…,,…,,,…,,…,…,…,……6-1
Periodic Inspection
6-1
Periodic maintenance
Chapter7- Troubleshooting and Fault Information.,…,,…,,,…,…,…,…7-1
Common problems and solutions
D..
Warning codes
7-4
M∨X9000 Parameter Listing……
B-1
20一 BASIC GROUPING( Quick Start)……
B-1
30--INPUTS
B-2
40- OUTPUTS
11面国面
50一 DRIVE CONTROL
60— MOTOR CONTROL
B-8
70— PROTECTIVE
B-9
80一 KEYPad/D| SPLAY
∴.B-10
90-COMMUNICATION PARAMETERS
B-12
Fuse Specification Chart....
Wiring Table
.C-2
All Braking Resistors Braking Units Used in AC Drives
EMI Filter Cross reference
EMI Filters
Din Rail Adapter(PN: MVXDR)……
C-9
Remote Kit(PN: MVXRM)………
C-10
xtension Input/Output(P/N: MVXEIO)
C-10
Cutler-Hammer MvX9000 User manual
Chapter 1-Introduction
This chapter describes the purpose and contents of this manual and the intended
audience. This chapter also explains conventions used in this manual and lists related
publications.
How to use This manual
The purpose of this manual is to provide you with information necessary to install, set
parameters, troubleshoot, and maintain the ac motor drives. To guarantee safe
operation of the equipment, read the safety guidelines at the beginning of this manual
before connecting power to the ac motor drives. Keep this operating manual handy
and distribute to all users for reference
Chapter 1-Introduction is the chapter you are reading now
Chapter 2-Overview of the MVX9000 Drive describes receiving and inspection
procedures and provides an introduction to digital keypad operation
Chapter 3- Storage and Installation describes planning for drive installation and drive
mounting This chapter also includes requirements and connections for wiring
Chapter 4- Start-up Procedures provides a detailed explanation of digital keypad
operation
Chapter 5-Descriptions of Parameter Setting provides detailed explanations for all
parameter settings.
Chapter 6-Maintenance and Inspection describes maintenance procedures
Chapter 7-Troubleshooting and Fault Information lists the fault displays
descriptions, and corrective actions
Appendix a-Technical Data lists standard specifications
Appendix b- Summary of Parameter Settings provides brief descriptions of all
parameters and their settings
Appendix C- Accessories provides information about circuit breakers, fuses, braking
resistors and other accessories for the cutler -Hammer mvx9000 drives
Appendix d- dimensions displays keypad and drive dimensions
Appendix E-is a Declaration of Conformity
Cutler-Hammer MvX9000 User manual
(系统自动生成,下载前可以参看下载内容)
下载文件列表
相关说明
- 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
- 本站是交换下载平台,提供交流渠道,下载内容来自于网络,除下载问题外,其它问题请自行百度。
- 本站已设置防盗链,请勿用迅雷、QQ旋风等多线程下载软件下载资源,下载后用WinRAR最新版进行解压.
- 如果您发现内容无法下载,请稍后再次尝试;或者到消费记录里找到下载记录反馈给我们.
- 下载后发现下载的内容跟说明不相乎,请到消费记录里找到下载记录反馈给我们,经确认后退回积分.
- 如下载前有疑问,可以通过点击"提供者"的名字,查看对方的联系方式,联系对方咨询.