ZT2835W0M1贴片发光二极管规格书.pdfZT2835W0M1贴片发光二极管规格书pdf,ZT

文件名称: ZT2835W0M1贴片发光二极管规格书.pdf

所属分类: 其它

开发工具:

文件大小: 824kb

下载次数: 0

上传时间: 2019-09-13

提供者: weixin_********

下载 (824kb)

不能下载？报告错误

详细说明：ZT2835W0M1贴片发光二极管规格书pdf,ZT2835W0M1贴片发光二极管规格书zT2835WOM1米米米(0.2W) CRI Ranks/ CRI/ CRI Ranks/ CRI/ CR⊥ Ranks/ CRI/ 档次显色性档次显色性档次显色性 RA70-75 RA80-8 RA90-95 RA8590 无显色要求 2 RA75-80 (Ra>60) Bin Range of Luminous Intensity亮度等级代码(T=25℃) Lumen ranks档次 uRiNous FI uX Lumen ranks档次 Luminous flux 光通量atT=60mA 光通量atI=60mA 18-22(1m) 2-26(1m) Bin Range of Forward Voltage电压等级代码(atIp=60mA,T=25%) 序 Forward Voltage止向电压电压电压范圉:2.8-3.6;按0.V分档。 voltage rang: 2.83.6 classify by 0. lv Part no. Description产品型号说明 2惠朿啸亮洗需科搞有公国區 zT2835WOM1米米米(0.2W) Z X XXX X X X X X X XX 65显色怛 5显色性75-80显色色 90-95显色忆95-100显色 33-3500K 品片数量四晶系列 2两晶系列五品系列 S-小功率系列卩-大功率系列发光颜色 0 o Orange(检)6UD=b15 amorEd(红) I615-635nm white(rD 220012000 nm BOBl:e(蓝) 450-475nn P0 Purple(紫 330±20nm G0 Green(绿) 510530n B13 icolo:(双色) Y0Ye11ow(黄) vGYe11 ow Green(黄绿) 565-575nm 七外型尺寸 28/5050/2835等 TOP LED 公冒名称代码票慕忠忘需科有熙公国區 zT2835WOM1米米米(0.2W) Color bin limit色度代码;(atIs=60mA,T=25C) 东莞中之光电白光分bin准 .42 L.4 1,3 0,36 0.3 1.32 1.28 1 32 34 360.380. 12 』40.6 票慕忠忘需科有熙公国區 zT2835WOM1米米米(0.2W) Color bin色坐标常用BIN区( Common bin) 序号 Color Bin色坐标可选BIN区( Optional bin) 序号 Color Bin色坐标票慕忠忘需科有熙公国區 zT2835WOM1米米米(0.2W) Typica1 Electro-0 ptical Characteristics Curves典型光一电特性曲线图 100 0- 2701-0r 30-50c FORMARDE让E阡Ts LUMTVOU3 NTENSITY V: FORARD/O__ TAGE 3L+5002V, 50)-,00c ength( nm) SPATIAL DISTRB/TOy nS So White FORWRD CUR,E PACKAGE0 UTLINE外形尺寸( Units:m 品的 0士0 .b士 SECTION -E Recommended Soldering推荐焊接模式票慕忠忘需科有熙公国區 zT2835WOM1米米米(0.2W) 一、 PRECAUT0 NS IN USE LED/使用LED注意事项; ed Soldering condition/LED焊接条件; l:烙铁焊接:烙铁最髙3σW尖端温度不超过300℃;焊接时不超过3秒; Manual soldering: iron Maximum 30w, iron bit temperature can not over 300 degree; soldering time should not be more than 3 seconds Cleanout/清洗; 当用化学品清洗LED胶体时须特别小心,因为有些化学品对胶体表面有损伤并引起裉色如三氯乙烯、丙酮, 可用乙醇擦拭浸渍,时间在常温下不超过2分钟。 Utmost care must be taken when using chemical to clean LED, Some chemical can damage the surface of epoxy and will cause colour fading, such as trichloroethylene, acetone etc ethanol can be used to wipe and dip under normal temperature, but the time should not be more than 3 minutes ESD Protecction/静电防护; 静电和电流的急剧升髙会对LED产生损伤,LED系列产品使用时请使用防静电装置,如防静电带和手套。 Excessive ESD and current could damage the Led, protection equipment such bands when operate Led Product。注意:使用时人体放电模式HBMK1000V;札器放电模式HBM<100V Attention: Human boby discharge Mode HBw<1000V: Machine discharge Mode MW<100V Reliability Test/可靠性试验; 我公司的LED产品不仅要经过生产线的自动分档测试仪检测、分档,而且要经过严格的可靠性试验,这些试验标准都是采用业内公认的MIL-STD Our ed chips are classified by machine in production line and strictly perfromed the reliability test according to world wide standard MIL-STD Test circuit测试电路; LED卓 Handling precautions处理注意事项 1.0 ver-current-proof过电流保护; Customer must apply resistors for protection; otherwise slight voltage shift will cause big current change(Burn out will happen) 客户必须采用电阻进行保护,否则辁微电压漂移将导致电流发生巨大变化 2. Storage Baking/储存烘烤; 2. 1 It is recommended to store the products in the following conditions推荐在下列环境下储仔: Humidity:60%R.H.Max.湿度:相对湿度≤60%; Temperature:5℃^30℃温度:5℃^30℃. 2. 2 Shelf life in sealed bag: 12 month at <5C 30C and <30%R H. after the package is opened the produc ts should be used within 24hrs or they should be kept stored at =20%RH. with zip-lock sealed. It is recommended to bake before soldering when the pack is unsealed after 24hrs. The conditions are as followings: 以密封袋储存保质期:12个月,5℃^30℃,相对湿度<30%。产品开封后应在24小时内使用,或在相对湿度三2%环境下储存,并以拉连锁密封。如包裝敞开超过τ小时,我们建议焊接前对产品进行烘烤。烘烤条件如下:80±3℃x(1012hrs)and<5‰RH。票慕忠忘需科有熙公国區 zT2835WOM1米米米(0.2W) Reflow Soldering Instruction回流焊说明; NOTE Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and second sol dering process.冋流焊接应该少于2次,在第一和第二次焊接之间要求有冷却至常温的过程. Test items and results of reliability信赖度测试项目; Number of 测试项目 Test Items 测试条件 Test Condition Note Damaged Therma1 Shock冷热冲击 40℃30mine100C30min 100 cycle 0/20 High Humidity heat cycle 25℃65℃90%24hrs/ Icycle 10 cvcle 0/20 高湿度热循 High Temperature Storage T=100℃ 高温贮存 1000 hrs 0/20 Humidity heat storage高湿度热 I=60°C’RH=90‰ 1000 hrs 贮存 Low Temperature Storage Ta =-40C 1000 hrs 0/20 低温贮存 Life test寿命试验 T。=25CIF=6OmA 1000 hrs 0/20 Life Test寿命试验 Ta =60C IF=60mA 1000 hrs 0/20 High Humidity heat life Test 0/20 高湿度热寿命试验 60℃CRH-90%I=60mA 500 hrs Low Temperature Life Test Ta--40℃IF-60mA 低温寿命试验 500 hrs 0/20 Resistance to soldering heat* TSOL=230°C,10sec 2 times 0/20 ( Reflow Soldering)回流焊试验 Human body model 500 v Electrostatic Discharge Test (forward and reverse current 0/ 静电放电试验 conduct electricity, cach 1 time) 票慕忠忘需科有熙公国區 zT2835WOM1米米米(0.2W) Taping specifications包装规格 REEL(178×8mm) Lak REL(0.075×220×210m) sture Barrier Bag REEL(105×184×184mm) 1. Package Quantity:2000pcs/Rel每卷2000颗 2. al dimens ions are in millimeters( tolerance:±0.2)所有尺寸单位为皿,公差为±0.2。票慕忠忘需科有熙公国區

(系统自动生成,下载前可以参看下载内容)