您好,欢迎光临本网站![请登录][注册会员]  
文件名称: mp2100a_opm_e_15_0.pdf
  所属分类: 网络安全
  开发工具:
  文件大小: 8mb
  下载次数: 0
  上传时间: 2019-09-03
  提 供 者: sunny*****
 详细说明:MP2100A-一体化比特误码率测试仪和眼图/脉冲示波器For Safety △ WARNING ALWAYS refer to the operation manual when working near locations at which the alert mark shown on the left is attached if the advice in the operation manual is not followed, there is a risk of personal injury or reduced equipment performance. The alert mark shown on the left may also be used with other marks and descriptions to indicate other dangers Overvoltage Categor This equipment complies with overvoltage category ll defined in IEC 61010. DO NOT connect this equipment to the power supply of overvoltage category Il or IV Laser radiation warning NEVER look directly into the cable connector on the equipment nor into the end of a cable connected to the equipment. There is a risk of injury if laser radiation enters the eye The Laser safety label is attached to the equipment for safety use as indicated in "Laser Safety"later in this section Electric Shock To ensure that the equipment is grounded, always use the supplied pin power cord, and insert the plug into an outlet with a ground terminal. If power is supplied without grounding the equipment, there is a risk of receiving a severe or fatal electric shock or causing damage to the internal components epaIr Only qualified service personnel with a knowledge of electrical fire and shock hazards should service this equipment. This equipment cannot △ WARNING NO OPERATOR SERVICE. be repaired by the operator. Do NOT attempt to remove the ABLE PARTS INSIDE equipment covers or unit covers or to disassemble internal REFER SERVICING TO QUALIFIED PERSONNEL components. There are high-voltage parts in this equipment presenting a risk of severe injury or fatal electric shock to untrained personnel. In addition, there is a risk of damage to precision components For Safety △ WARNING Calibration The performance-guarantee seal verifies the integrity of the equipment SEAL To ensure the continued integrity of the equipment, only Anritsu service personnel, or service personnel of an Anritsu sales o Anritsu u representative, should break this seal to repair or calibrate the equipment. Be careful not to break the seal by opening the N equipment or unit covers. If the performance-guarantee seal is broken by you or a third party, the performance of the equipment cannot be guaranteed Falling over This equipment should always be positioned in the correct manner. If the cabinet is turned on its side, etc, it will be unstable and may be damaged if it falls over as a result of receiving a slight mechanical shock Always set up the equipment in a position where the power switch can be reached without difficulty Replacing Battery When replacing the battery, use the specified battery and insert it with the correct polarity. If the wrong battery is used, or if the battery is inserted with reversed polarity, there is a risk of explosion causing severe injury or death Battery Fluid DO NOT short the battery terminals and never attempt to disassemble the battery or dispose of it in a fire. If the battery is damaged by any of these actions, the battery fluid may leak. This fluid is poisonous DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is accidentally ingested, spit it out immediately, rinse your mouth with water and seek medical help. If it enters your eyes accidentally, do not rub your eyes, rinse them with clean running water and seek nedical help. If the liquid gets on your skin or clothes, wash it off carefully and thoroughly Battery Disposal Do NoT expose batteries to heat or fire Do not expose batteries to fire. This is dangerous and can result in explosions or fire. Heating batteries may cause them to leak or explode For Safety △ WARNING LCD This equipment uses a Liquid Crystal Display(LCD) Do NOT subject the equipment to excessive force or drop it If the lCd is subjected to strong mechanical shock, it may break and liquid may leak This liquid is very caustic and poisonous DO NOT touch it, ingest it, or get in your eyes. If it is ingested accidentally, spit it out immediately, rinse your mouth with water and seek medical help. If it enters your eyes accidentally, do not rub your eyes, rinse them with clean running water and seek medical help. If the liquid gets on your skin or clothes, wash it off carefully and thoroughly For Safety △ CAUTION Cleaning Always remove the main power cable from the power outlet before cleaning dust around the power supply and fan Clean the power inlet regularly. If dust accumulates around the power pins, there is a risk of fire Keep the cooling fan clean so that the ventilation holes are not obstructed. If the ventilation is obstructed, the cabinet may overheat and catch fire Check Termina Never input a signal of more than the indicated value between the measured terminal and ground. Input of an excessive signal may damage the equipment For Safety Laser safety Class 1 indicates the danger degree of the laser radiation specified below according to IEC 60825-1: 2007 Class 1: Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing Class I indicates the degree of danger of the laser radiation outlined below as defined by 21 CFR 1040.10: 1995 Class l: Class levels of laser radiation are not considered to be hazardous △ WARNING The laser in this equipment is classified as Class 1 according to the IEC 60825-1: 2007 standard, or as class i according to the 21 CFR 1040.10:1995 standard △ CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure The use of optical instruments with this product will increase eye nazal Ird For Safety Laser Safety The model names of " recommended sfpixep written on label are listed in following table Table 1 Laser Safety Classifications Based on IEC 60825-1: 2007 Beam Max Optical Emitted Pulse Width(s)/ Radiation Model Name Class Output Power Wavelength Angle (mW) Repetition Rate (nm) Aperture Ideg. I G0174A 0.78 850 Ccd MwW 23.0 Figure 2 G0194A 0.8 1310 11.5 Figure 2 [1] G0195A 1.58 1550 11.5 Figure 2 [1] G0238A 0.8 CW 850 23.0 Figure 2[1 G0239A 1.12 CW 1310 115 Figure 2 [ Indicates the possible optical output power when each and every reasonably foreseeable single-fault condition is included Table 2 Specifications of Laser Built into MP2100A/MP2101A Max Optica Pulse Width(s) Emitted Radiation Model Name Output Power Repetition Rate Wavelength Angle (mW) Ideg. G0174A 0.78 CW 850 23.0 G0194A 0.8 CW 1310 G0195A 1.58 CW 1550 11.5 G0238A 0.8 CW 850 23.0 G0239A 1.12 CW 1310 11.5 Indicates the possible optical output power when each and every oly foreseeable single-fault condition is included For Safety Table3 labels on product Type Label Affixed to: Model name MP2100A+ MP2100A-050 MP2100A+ △1Ec60825-1:2007 MP2100A-051, 1 Explanation CLASS 1 LASER PRODUCT Figure 1, A MP2101A+ MP2101A-050, MP2101A+ MP2101A-051 MP2100A+ MP2100A050 CERTIFICATION LABEL MP2100A+ Certification THIS PRODUCT CONFORMS To Figure 1.B MP2100A-051 ALL APPLICABLE STANDARDS MP2101A+ UNDER 21 CFR 1040.10 MP2101A-050 MP2101A+ MP2101A-051 MP2100A+ MP2100A-050, DENTIFICATION LABEL MP2100A ANRITSU CORP MP2100A-051 3 Identification 5-1-1. ONNA, ATSUGI-SHI KANAGAWA 243-8555,JAPAN Figure 1, C MP2101A+ MANUFACTURED ATTOHOKU ANRITSU CO. LTD MP2101A-050 KORMYAMA PLANT MP210IA MP2101A-051 IX For Safety Laser radiation Markings C 急 A Figure 1 Locations of Affixed Labels aIi.EMP2100A=·SRW PPGD PP 1 aa"以‖‖ Figure 2 Locations of Laser Beam Apertures
(系统自动生成,下载前可以参看下载内容)

下载文件列表

相关说明

  • 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
  • 本站是交换下载平台,提供交流渠道,下载内容来自于网络,除下载问题外,其它问题请自行百度
  • 本站已设置防盗链,请勿用迅雷、QQ旋风等多线程下载软件下载资源,下载后用WinRAR最新版进行解压.
  • 如果您发现内容无法下载,请稍后再次尝试;或者到消费记录里找到下载记录反馈给我们.
  • 下载后发现下载的内容跟说明不相乎,请到消费记录里找到下载记录反馈给我们,经确认后退回积分.
  • 如下载前有疑问,可以通过点击"提供者"的名字,查看对方的联系方式,联系对方咨询.
 相关搜索: mp2100a_opm_e_15_0.pdf
 输入关键字,在本站1000多万海量源码库中尽情搜索: