您好,欢迎光临本网站![请登录][注册会员]  
文件名称: 轨到轨四运放, 3.0V~36V, 汽车级工作温度-40~125℃,低偏置,低温漂-TPH2504.pdf
  所属分类: 其它
  开发工具:
  文件大小: 922kb
  下载次数: 0
  上传时间: 2019-09-03
  提 供 者: weixin_********
 详细说明:轨到轨四运放, 3.0V~36V, 汽车级工作温度-40~125℃,低偏置,低温漂-TPH2504.pdfTPH2501/TPH2502/TPH2503/TPH2504 250MHz, Precision, Rail-to-Rail l/o, CMOS Eleetrieal haraeteristies The specifications are at TA=+25C, RF=0Q, RL= lkQ, and connected to vs/2, Unless otherwise noted SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Input offset voltage VCM=VDD/2+0.5V 500 ±50 +500 p Vos Tc Input Offset Voltage Drift 40°Cto125°0 2 pv/° TA=27°C A Input bias current TA=85°C 150 A TA=125°C A Input Offset Current 0.001 e Input Voltage Noise Density =1MHz 65 nV/vHz Input Current Noise 50 fA√VHz Differential 2.7 CIN Input Capacitance Common mode CMrr Common Mode Rejection Ratio VaM=-1V to 3V, Vs=5.4V dB Common-mode Input Voltage V--0.1 V+-0.1 Range PsRR Power Supply Rejection Ratio VcM=Vs/2 Vs=2.4V to 5.5V 120 dB A Open-Loop Large Signal Gain RLOAD =2K22 110 dB Frequency Response G=+1, Vo= 100m VpP, RE= 250 250 Small-Signal Bandwidth G=+2, Vo= 100mVpp 90 MHZ GBW Gain-Bandwidth Product G=+10 120 MH f01 Bandwidth for o 1 db gain Flatness G=+2, Vo= 100mVpp 25 MHZ Vs=+5V, G=+1, 4V ster 200 V/us sr Slew Rate Vs=+5V,G=+1, 2V Step 180 V/us Vs=+3V,G=+1, 2V Step 160 V/us G=+1,Vo=200mvpP,10%to90% 2 ns tF Rise-and-Fall Time G=+1,Vo=2vp,10%to90% 7 Settling Time, 0.1% Vs=+5V, G=+1, 2V Output Step 25 ts Settling time, 0.01% 40 ns tR Overload recovery time ∨N+Gain=Vs 50 ns HD2 Harmonic Distortion G=+1. f= 1MHZ, Vo 2VPP, Rl= 200Q 2nd-Harmonic VcM=1.5V dBc Harmonic distortion HD3 G=+1.f=1MHZ. Vo 2VPP, Rl= 2000 90 dBc rd-harmonIc VCM=1.5V Differential gain error NTSC. RL= 150Q 0.02 % PE Differential Phase Error NTSC. RL=150Q 03 degrees Channel-to-Channel crosstalk TPH2502 -100 Channel-to-Channel crosstalk f= 5MHz 84 dB TPH2504 www.3peakic.Com Rev.A TPH2501/TPH2502/TPH2503/TPH2504 250MHZ, Precision Rail-to-Rail I/O, CMOS Op-amps Eleetrieal haraeteristies The specifications are at TA=+25C, RF=0Q, RL= lkQ, and connected to vs/2, Unless otherwise noted SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Output Swing from Supply Rail RLOAD= 100kn Differential 10132 Q‖lpF R Input Impedance Common-Mode 10132 Q pF R Closed-Loop Output Impedance G=1, f=1kHZ, lOUT =0 0.01 Ro Open-Loop Output Impedance f=1kHz, loT=0 Q Sink current 100 160 mA Isc Output Short-Circuit Current Source current 100 290 A Supply∨o|taqe 2.5 55 Quiescent Current per Amplifier 65 7.5 mA Shutdown Current(TPH2503) 5 Rev,A www.3peakic.com TPH2501/TPH2502/TPH2503/TPH2504 250MHz, Precision, Rail-to-Rail l/o, CMOS TypiCal Performanee haraeteristies Vs=5V,G=+, RF=0Q, RL=1kQ, and connected to Vs/2, unless otherwise specified Noninverting Small-Signal Frequency Response Inverting Small-Signal Frequency Response 5 Vo=0.iVpp G=1,R==240 V=0.1V G=-1,R=6209 0 巴EE G=2,R==62002 E三 G=-2,RF=6200 G=5.RF=620 G=5,RF=6200 G=-10.R=6209 G=10,R=6200 1000M 100k 1M 100M 1000M Fre Frequency(Hz) Frequency Response for Various C Noninverting Small-Signal Step Response 0 In put OUtput N CL=47PR 15 Ci =5.6pF 20 1M Frequency(Hz) Time(20ns/div) Inverting Large-signal Step Response Quiescent Current VS Temperature s=+5V In put 6 st=Output V=+2.5V 50250 Time(20ns/div) Temperature(℃) www.3peakic.com Rev.A TPH2501/TPH2502/TPH2503/TPH2504 250MHZ, Precision Rail-to-Rail I/O, CMOS Op-amps TypiCal Performanee haraeteristies Vs=5V,G=+1, R=0Q, Rl=1kQ2, and connected to v$/2, unless otherwise specified CMRR and PSRR Vs Temperature Frequency Response For Various RL 160 140 RL= 10kQ2 PSRR 120 m100 CMRR R-=0 V。=0.1V R=1ka什 R1=100 o60 RL=509 9 20 0 75100125 100 1M 10M 10M 1o00M Temperature(℃ Frequency (Hz) Frequency Response Vs Capacitive Load Channel-To-Channel crosstalk G=+1 CL =5.6pf, Rs=oQ V=0.1V 100 CL=47pf Rs =50Q2 C1=100pf,Rs=30Q -6 兰 -9 10M 10M 1000M 100k 100M 1000M Frequency(Hz) Frequency(Hz) Closed-Loop Output Impedance Vs Frequency Voltage Spectral Density Vs. Frequency N三 l00 C.01 100k 10M 100M 1000M Frequency(Hz) Frequency(Hz) Rev,A www.3peakic.com TPH2501/TPH2502/TPH2503/TPH2504 250MHz, Precision, Rail-to-Rail l/o, CMOS TypiCal Performanee haraeteristies Vs=5V,G=+, RF=0Q, RL=1kQ, and connected to Vs/2, unless otherwise specified Open L°。 p Gain Vs. Temperature Open Loop Gain And Phase 140 Phase 120 aln 20 70 Temperature(℃) Frequency(Hz) nput Bias current vs Temperature 0.9 08 0.6 0.4 0.3 0.1 0.1 10 Temperature(℃) www.3peakic.com Rev.A TPH2501/TPH2502/TPH2503/TPH2504 250MHZ, Precision, Rail-to-Rail I/o, CMOS Op-amps Pin naTions -IN: Inverting Input of the Amplifier V-or-Vs: Negative Power Supply It is normally tied to +IN: Non-Inverting Input of Amplifier. ground. It can also be tied to a voltage other than ground OUT: Amplifier Output The voltage range extends to as long as the voltage between v+ and v-is from 2. 5v to within mv of each supply rail 5.5V. If it is not connected to ground, bypass it with a V+ or +Vs: Positive Power Supply. Typically the voltage capacitor of 0. 1uf as close to the part as possible is from 2. 5V to 5.5V. Split supplies are possible as long SHDN: High on this pin logic low to shut down the as the voltage between v+ and v-is between 2.5V and device. Range Logic high enables the device and 5.5V. A bypass capacitor of 0. 1pF as close to the part as logic low shut down the device. This pin defaults to possible should be used between power supply pins or logic high if left open. between supply pins and ground Operati。m The TPH2501, TPH2502, TPH2504 is a CMOS, rail-to-rail IO, high-speed, voltage-feedback operational amplifier designed for video, high-speed and other applications It is available as a single, dual, or quad op amp. the amplifier features a 250MHz gain bandwidth, and 180V/us slew rate, but it is unity-gain stable and can be operated as a+1V/ voltage follower. The TPH2501/TPH2502/TPH2504 is specified over a power-supply range of +2.7V to +5.5V(+1.35V to #2.75V). However, the supply voltage may range from +2. 5V to +5. 5V(+1.25V to +2.75V). Supply voltages higher than 7.5v (absolute maximum) can permanently damage the amplifier. Parameters that vary over supply voltage or temperature are shown in the typical characteristics section of this datasheet Applications Information Rail-to-Rail Inputs and outputs The TPH2501, TPH2502, TPH2504 op amps are designed to be immune to phase reversal when the input pins exceed the supply voltages, therefore providing further in-system stability and predictability. Figure 1 shows the input voltage exceeding the supply voltage without any phase reversal 3As=+2.5 V -500-250 007501000 Time (us) Figure 1. No Phase Reversal Choice of feedback resistor and gain bandwidth product For applications that require a gain of +1, no feedback resistor is required. Just short the output pin to the inverting input pin For gains greater than +1, the feedback resistor forms a pole with the parasitic capacitance at the inverting ReV,A www.3peakic.com TPH2501/TPH2502/TPH2503/TPH2504 250MHZ, Precision, Rail-to-Rail l/O, CMOS input. As this pole becomes smaller, the amplifier,'s phase margin is reduced. This causes ringing in the time domain and peaking in the frequency domain. Therefore, Rp has some maximum value that should not be exceeded for optimum performance. If a large value of r must be used, a small capacitor in the few Pico farad range in parallel with RF can help to reduce the ringing and peaking at the expense of reducing the bandwidth. As far as the output stage of the amplifier is concerned, the output stage is also a gain stage with the load RF and RG appear in parallel with RL for gains other than +1. As this combination gets smaller, the bandwidth falls off. Consequently, RF also has a minimum value that should not be exceeded for optimum performance. For gain of +1, R=0 is optimum. For the gains other than +1, optimum response is obtained with ro between 3000 to 1 kQ2 The TPH2501, TPH2502 and TPH2504 have a gain bandwidth product of 120MHz For gains 25, its bandwidth can be predicted by the following equation Gain x BW=120MHz Video performance For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. This is especially difficult when driving a standard video load of 150Q because the change in output current with DC level. Special circuitry has been incorporated in the TPH2501, TPH2502 and TPH2504 to reduce the variation of the output impedance with the current output. This results in dG and dP specifications of 0. 03% and 0.3, while driving 150Q at a gain of 2. Driving high impedance loads would give a similar or better dG and dP performance Driving Capacitive Loads and cables The TPH2501, TPH2502 and TPH2504 can drive 10pF loads in parallel with 1kQ2 with less than 5dB of peaking at gain of +1. If less peaking is desired in applications, a small series resistor (usually between 50 to 50Q)can be placed in series with the output to eliminate most peaking. However, this will reduce the gain slightly. If the gain setting is greater than 1, the gain resistor RG can then be chosen to make up for any gain loss which may be created by the additional series resistor at the output. When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications a back-termination series resistor at the amplifier's output will isolate the amplifier from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. Again, a small series resistor at the output can help to reduce peaking Output Drive Capability The TPH2501, TPH2502 and TPH2504 output stage can supply a continuous output current of +100mA and still provide approximately 2.7V of output swing on a 5V supply. For maximum reliability, it is not recommended to run a continuous DC current in excess of +100mA. Refer to the typical characteristic curve Output Voltage Swing vs Output Current. For supplying continuous output currents greater than +100mA, the TPH250x may be operated in parallel. the tPh250X will provide peak currents up to 200mA, which corresponds to the typical short-circuit current. Therefore, an on-chip thermal shutdown circuit is provided to protect the TPH250x from dangerously high junction temperatures. At 160C the protection circuit will shut down the amplifier. Normal operation will resume when the junction temperature cools to below140°C. www.3peakic.com Rev.A TPH2501/TPH2502/TPH2503/TPH2504 250MHZ, Precision, Rail-to-Rail I/o, CMOS Op-amps Single Supply video Line Driver The TPH2501, TPH2502 and TPH2504 are wideband rail-to-rail output op amplifiers with large output current, excellent dG, dP, and low distortion that allow them to drive video signals in low supply applications. Figure 2 is the single supply non-inverting video line driver configuration inverting video ling driver configuration. the signal is Ac coupled by c1 R1 and R2 are used to level shift the input and output to provide the largest output swing RF and RG set the ac gain. C2 isolates the virtual ground potential. RT and R3 are the termination resistors for the line C1, C2 and C3 are selected big enough to minimize the droop of the luminance signal 47F 470F TPH250 75n 75 220uF 工 47F500 v R 750 75Q 10K 10K 220μF Figure 2. 5V Single Supply Non-Inverting and Inverting Video Line Driver Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, a good printed circuit board layout is necessary for optimum performance. Lead lengths should be as sort as possible. The power supply pin must be well bypassed to reduce the risk of oscillation. For normal single supply operation, where the Vs- pin is connected to the ground plane, a single 4.7uF tantalum capacitor in parallel with a 0. 1uF ceramic capacitor from Vs+ to gnd will suffice. This same capacitor combination should be placed at each supply pin to ground if split supplies are to be used. In this case, the vs- pin becomes the negative supply rail For good AC performance, parasitic capacitance should be kept to a minimum Use of wire wound resistors should be avoided because of their additional series inductance. Use of sockets should also be avoided if possible Sockets add parasitic inductance and capacitance that can result in compromised performance. Minimizing parasitic capacitance at the amplifier's inverting input pin is very important the feedback resistor should be placed very close to ReV,A www.3peakic.com
(系统自动生成,下载前可以参看下载内容)

下载文件列表

相关说明

  • 本站资源为会员上传分享交流与学习,如有侵犯您的权益,请联系我们删除.
  • 本站是交换下载平台,提供交流渠道,下载内容来自于网络,除下载问题外,其它问题请自行百度
  • 本站已设置防盗链,请勿用迅雷、QQ旋风等多线程下载软件下载资源,下载后用WinRAR最新版进行解压.
  • 如果您发现内容无法下载,请稍后再次尝试;或者到消费记录里找到下载记录反馈给我们.
  • 下载后发现下载的内容跟说明不相乎,请到消费记录里找到下载记录反馈给我们,经确认后退回积分.
  • 如下载前有疑问,可以通过点击"提供者"的名字,查看对方的联系方式,联系对方咨询.
 输入关键字,在本站1000多万海量源码库中尽情搜索: